New steering box questions?
02-10-2022, 07:16 AM
#1
Junior Member
Thread Starter
Join Date: Sep 2014
Posts: 48
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Iroc-Z
Engine: Carbed 350
Transmission: TH350
New steering box questions?
Hi everyone!
I just replaced my leaking lares 1282 steering box with new unit lares 11282…but i have a problem.
The steering is working fine and all but the steering wheel is off to the right side i would say around 30 degrees.
When i took everything off it was all in center - the wheels and steering wheel… New steering box was centered but when comparing old unit to new i already saw that input shaft was clocked more right than the old acording to flat spot on the input shaft.
I dont think you could mess the install because pitman arm only goes one way cause of 4 notches that are 90 degrees apart and the steering shaft has flat spot that only goes one way.
Now for the question i cant wrap my head around.
If i adjust tie rods to make the steering centered then the input shaft on the new box would be more to the left and so off the box center?
I hope you understand what i mean…
Thank you all.
I just replaced my leaking lares 1282 steering box with new unit lares 11282…but i have a problem.
The steering is working fine and all but the steering wheel is off to the right side i would say around 30 degrees.
When i took everything off it was all in center - the wheels and steering wheel… New steering box was centered but when comparing old unit to new i already saw that input shaft was clocked more right than the old acording to flat spot on the input shaft.
I dont think you could mess the install because pitman arm only goes one way cause of 4 notches that are 90 degrees apart and the steering shaft has flat spot that only goes one way.
Now for the question i cant wrap my head around.
If i adjust tie rods to make the steering centered then the input shaft on the new box would be more to the left and so off the box center?
I hope you understand what i mean…
Thank you all.
Last edited by klein; 02-10-2022 at 07:20 AM.
02-17-2022, 07:49 PM
#3
Supreme Member
iTrader: (1)
Join Date: Sep 2005
Posts: 26,112
Received 1,686 Likes
on
1,281 Posts
Car: Yes
Engine: Usually
Transmission: Sometimes
Axle/Gears: Behind me somewhere
Re: New steering box questions?
When you called and asked and talked to them about it, what did Lares say?
02-18-2022, 01:21 AM
#4
Junior Member
Thread Starter
Join Date: Sep 2014
Posts: 48
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Iroc-Z
Engine: Carbed 350
Transmission: TH350
Re: New steering box questions?
This is what they said…
Hello,
Since there are 4 flats on the sector shaft, the steering wheel would be at center at 12 o’clock. If the gear box would be installed off center, then the only other possibilities because there are 4 flats would be that the steering wheel would be off center at either 3 o’clock, 6 o’clock or 9 o’clock. If your steering wheel is off less than a ¼ of a turn than most likely would be a front end issue.
Since there are 4 flats on the sector shaft, the steering wheel would be at center at 12 o’clock. If the gear box would be installed off center, then the only other possibilities because there are 4 flats would be that the steering wheel would be off center at either 3 o’clock, 6 o’clock or 9 o’clock. If your steering wheel is off less than a ¼ of a turn than most likely would be a front end issue.
06-11-2022, 09:45 AM
#5
Senior Member
Join Date: Dec 2001
Location: Cheektowaga., NY, USA
Posts: 862
Likes: 0
Received 3 Likes
on
2 Posts
Car: 91 Camaro RS
Engine: 305 TBI LO3
Re: New steering box questions?
Did you check the box before you installed it to make sure the steering was centered. Put a set of vice grips on the input shaft where the steering column would go. Turn it all the way left. Then all the way right, counting how many complete rotations you turn. Then go back to half the amount of full turns (center). Odds are it didn't ship centered and you installed assuming it was.
Thread
Thread Starter
Forum
Replies
Last Post
91 camaro racer
Suspension and Chassis
7
02-04-2015 12:24 AM