Chocolate Milk for power steering fluid
#1
Junior Member
Thread Starter
Join Date: Nov 2015
Location: Kingsley, MI
Posts: 60
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1987 IROC-Z
Engine: 5.7L TPI
Transmission: 700R4
Axle/Gears: Borg Warner 9 bolt with 3.27
Chocolate Milk for power steering fluid
As many of you probably know I'm in the process of tearing into my motor a bit this winter and one item that I have found neglected by the PO was the power steering. Pulling the pump revealed chocolate milk in the reservoir and the lines look like the originals so I'm planning on replacing the pump and the soft lines. But, does anyone have suggestions as to how I can get all the old fluid out of the steering gear box and cooler lines? Is there a good way to flush this? Thanks ya'll.
#2
Member
Join Date: Aug 2009
Location: Escondido, Ca
Posts: 384
Likes: 0
Received 1 Like
on
1 Post
Car: 1985 Trans Am
Engine: LG4
Transmission: 700R4
Axle/Gears: 3.08
Re: Chocolate Milk for power steering fluid
A cheap turkey baster comes in handy for just such occasions. Since you've already pulled the pump, you can spin the shaft and it should pump out any fluid in the lines. I had a leaking pump shaft seal so I replaced mine. I rented a puller from Autozone to transfer the pulley from the pump. It worked perfectly!
#3
Supreme Member
iTrader: (11)
Join Date: Sep 1999
Location: NJ
Posts: 4,345
Received 298 Likes
on
234 Posts
Car: 92 Firebird
Engine: 4.8 LR4
Transmission: T56
Axle/Gears: 3.45 9 Bolt
Re: Chocolate Milk for power steering fluid
I think getting the crap out of the box will be the biggest problem. I recently had to clean out burned fluid out of my car. Right or wrong, I just drained the reservoir, filled the system, started car, turned wheel side to side a bunch of times and repeated about 6 times. After I did it 6 times the fluid smelled a lot less burned and was mostly clear after that.
#4
Junior Member
Thread Starter
Join Date: Nov 2015
Location: Kingsley, MI
Posts: 60
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1987 IROC-Z
Engine: 5.7L TPI
Transmission: 700R4
Axle/Gears: Borg Warner 9 bolt with 3.27
Re: Chocolate Milk for power steering fluid
I thought about doing something similar. I was considering getting a new pump installed and just hook up the discharge to gearbox while capping the return at the pump. Then run the return line from the radiator into a bucket and keep adding fluid with the car running until it runs clear. Not sure if I can do all that with it running but theoretically you should be able to push all the old crap right through right?
#5
Member
Join Date: Aug 2009
Location: Escondido, Ca
Posts: 384
Likes: 0
Received 1 Like
on
1 Post
Car: 1985 Trans Am
Engine: LG4
Transmission: 700R4
Axle/Gears: 3.08
Re: Chocolate Milk for power steering fluid
Sorry, I misread your post. I thought you were talking about the pump. I agree with scooter that once you put fresh fluid in the pump, there should be no further problems. The gearbox doesn't hold very much. Turning the wheels from side to side after the system is back together and the engine is running, removes the air from the system. You could check the condition of your fluid at that time and decide if it needs to be sucked out.
#6
Junior Member
Thread Starter
Join Date: Nov 2015
Location: Kingsley, MI
Posts: 60
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1987 IROC-Z
Engine: 5.7L TPI
Transmission: 700R4
Axle/Gears: Borg Warner 9 bolt with 3.27
Re: Chocolate Milk for power steering fluid
10-4. I'll give it a try and see what happens after getting all I can out of the gearbox. Thank you.
#7
Supreme Member
iTrader: (1)
Join Date: Sep 2005
Posts: 26,155
Received 1,694 Likes
on
1,287 Posts
Car: Yes
Engine: Usually
Transmission: Sometimes
Axle/Gears: Behind me somewhere
Re: Chocolate Milk for power steering fluid
You can disconnect the return line from the pump, plug the hole in the pump, start the motor with the line pointing into a catch can of some sort, and add fluid to the reservoir as it comes out the return line. Should flush it all out within a few seconds.
Trending Topics
#8
Junior Member
Thread Starter
Join Date: Nov 2015
Location: Kingsley, MI
Posts: 60
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1987 IROC-Z
Engine: 5.7L TPI
Transmission: 700R4
Axle/Gears: Borg Warner 9 bolt with 3.27
Re: Chocolate Milk for power steering fluid
Thanks Sofa. That's what I'm going to try. Hopefully I can do that without losing any fingers! Lots of moving parts.
Thread
Thread Starter
Forum
Replies
Last Post
Graboid
Auto Detailing and Appearance
65
06-23-2003 07:31 PM