Project Stealth Ram AFR has begun - Updated peiodically
08-30-2002, 03:03 PM
#1
Supreme Member
Thread Starter
Join Date: Sep 2000
Location: Michigan
Posts: 1,230
Likes: 0
Received 0 Likes
on
0 Posts
Project Stealth Ram AFR has begun - Updated peiodically
Well folks I've finally got everything together. Here will be my setup on my 355 small block:
-Holley Stealth Ram Intake
-AFR 195cc heads milled to 64cc chambers
-Comp cam - 230/236 dur. @.050", .510/.520 lift, 110 lobe sep
I will be keeping the stock throttle body and I will use 24# injectors. I will also be reprogramming the prom. Behind the engine will be my current 700R4 trans with a 2200 stall speed converter, and a 3.42 posi rear end. I've also already installed a Spohn torque arm, Spohn lower control arms, and control arm relocation brackets to put the power on the ground.
I am hoping to run in the mid-low 12 second range with this setup and some tuning. I will be updating this post as my work progresses. Finally we'll know what kind of real power this Stealth Ram can make. Any opinions/suggestions would be greatly appreciated. Thanks.
-Holley Stealth Ram Intake
-AFR 195cc heads milled to 64cc chambers
-Comp cam - 230/236 dur. @.050", .510/.520 lift, 110 lobe sep
I will be keeping the stock throttle body and I will use 24# injectors. I will also be reprogramming the prom. Behind the engine will be my current 700R4 trans with a 2200 stall speed converter, and a 3.42 posi rear end. I've also already installed a Spohn torque arm, Spohn lower control arms, and control arm relocation brackets to put the power on the ground.
I am hoping to run in the mid-low 12 second range with this setup and some tuning. I will be updating this post as my work progresses. Finally we'll know what kind of real power this Stealth Ram can make. Any opinions/suggestions would be greatly appreciated. Thanks.
08-30-2002, 03:10 PM
#2
Supreme Member
Join Date: Apr 2000
Location: Stillwater, OK
Posts: 1,154
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Formula
Engine: 355 DFI Superram w/ R-Trim
Transmission: Probuilt 700r4
You're a copy cat dude! Just kidding...
Mine is a 4bolt 355, forged rotating assy 10.7:1...everything being the exact same pretty much cept I have a lingenfelter 58mm tb, longtubes, svo 30#s, and 3.73s. Here is a picture...it's still on the stand. I hope to run mid to low 11s or high 10s using a 150 shot. Oh, my cam is hyd roller 224/244 110 .560/.560 and crane golds. I think you'll have the times you want with that combo!
Mine is a 4bolt 355, forged rotating assy 10.7:1...everything being the exact same pretty much cept I have a lingenfelter 58mm tb, longtubes, svo 30#s, and 3.73s. Here is a picture...it's still on the stand. I hope to run mid to low 11s or high 10s using a 150 shot. Oh, my cam is hyd roller 224/244 110 .560/.560 and crane golds. I think you'll have the times you want with that combo!
08-30-2002, 03:14 PM
#3
Member
iTrader: (2)
Join Date: Sep 1999
Location: Canada
Posts: 384
Likes: 0
Received 2 Likes
on
2 Posts
Car: 92 quasar gta
Engine: Nothing
Transmission: Nothing
Axle/Gears: 4.11s
Looks like a good combination. Is there a reason your sticking with the stock TB? that might choke it down a bit...
what ratio of rockers are you using?
im going to be trying the same setup (maybe a bit bigger cam).. but almost exact to what your doing... keep us informed
what ratio of rockers are you using?
im going to be trying the same setup (maybe a bit bigger cam).. but almost exact to what your doing... keep us informed
08-30-2002, 03:27 PM
#4
Supreme Member
Thread Starter
Join Date: Sep 2000
Location: Michigan
Posts: 1,230
Likes: 0
Received 0 Likes
on
0 Posts
Well, I'm sticking with the stock tb for now for two reasons. 1. I'm short on cash enough as it is already, and 2. From what I've heard the stock one isn't really a restriction. Someone correct me if I'm wrong, but don't they use a 48mm tb on the big ram jet motors? Also, I'm using 1.5 rockers, as if I go too much more I run into the issue of valve/piston clearance, since my block was zero-decked. Besides, the .510/.520 lift should be sufficient enough. Thanks.
08-30-2002, 03:40 PM
#5
Member
iTrader: (2)
Join Date: Sep 1999
Location: Canada
Posts: 384
Likes: 0
Received 2 Likes
on
2 Posts
Car: 92 quasar gta
Engine: Nothing
Transmission: Nothing
Axle/Gears: 4.11s
id like to know about the TB as well... i have an air foil on mine so it flows a touch better... id like not to replace it if I dont have to as it costs more then the entire stealth ram.. hows is that freaking possible?
that cam should be awesome for your setup... did you work the heads at all or are the right outta the box?
that cam should be awesome for your setup... did you work the heads at all or are the right outta the box?
Trending Topics
08-31-2002, 02:26 AM
#12
Senior Member
Originally posted by bbunting
rezinn-why does the Stealth Ram choke at 672 HP? Is that NA HP?
rezinn-why does the Stealth Ram choke at 672 HP? Is that NA HP?
09-02-2002, 12:29 AM
#13
Supreme Member
Thread Starter
Join Date: Sep 2000
Location: Michigan
Posts: 1,230
Likes: 0
Received 0 Likes
on
0 Posts
Sorry for not updating. The project is on hold right now over the long Labor Day weekend. I found out I won't be able to have my cam degreed until Sunday, so I'll probably start tearing the motor down on Wednesday. Thanks.
09-07-2002, 12:11 AM
#14
Supreme Member
Thread Starter
Join Date: Sep 2000
Location: Michigan
Posts: 1,230
Likes: 0
Received 0 Likes
on
0 Posts
Update:
I've got almost everything torn down and disconnected. I just need to yank the heads and the cam. The cam will be put in and degreed on Sunday, and I will also bolt on the new heads and intake. Hopefully if I have time I'll be able to connected the fuel rails too. Then between Monday, Tuesday, and Wednesday I will do the final bolt-ons, and do a quick PROM burn for the initial startup. I plan on cutting all me VE tables by 25% in the idle range, and leaving everything else the way it is. Hopefully if all goes well I will be starting this bad boy up on Wednesday. I'll keep you posted. Thanks.
I've got almost everything torn down and disconnected. I just need to yank the heads and the cam. The cam will be put in and degreed on Sunday, and I will also bolt on the new heads and intake. Hopefully if I have time I'll be able to connected the fuel rails too. Then between Monday, Tuesday, and Wednesday I will do the final bolt-ons, and do a quick PROM burn for the initial startup. I plan on cutting all me VE tables by 25% in the idle range, and leaving everything else the way it is. Hopefully if all goes well I will be starting this bad boy up on Wednesday. I'll keep you posted. Thanks.
09-11-2002, 01:54 PM
#15
Supreme Member
Thread Starter
Join Date: Sep 2000
Location: Michigan
Posts: 1,230
Likes: 0
Received 0 Likes
on
0 Posts
Well, things haven't gone as fast as I'd like them to. The old intake, heads, and cam are all the way off. The new cam is in. I just have to get it degreed. I bought the degree kit and the piston stop so I could do it with the heads off. My problem is the instructions are for doing it with the heads on. Does anyone know what is different in the procedure for using the piston stop?? Thanks.
03-28-2003, 08:13 PM
#16
Member
Join Date: Jun 2002
Location: CR, Iowa
Posts: 254
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1990 IROC Z
Engine: blown 390 CI
Transmission: TKO II
Originally posted by Odyssey
Actually what he ment was 674.231 HP. And of course that's not N/A. It's /N/A/W/S HP!
Actually what he ment was 674.231 HP. And of course that's not N/A. It's /N/A/W/S HP!
Thread
Thread Starter
Forum
Replies
Last Post
