Just got SLP/Catco/Flowmaster installed and car barely runs
#1
Junior Member
Thread Starter
Join Date: Jan 2004
Location: Charlotte, NC
Posts: 6
Likes: 0
Received 0 Likes
on
0 Posts
Car: POS
Just got SLP/Catco/Flowmaster installed and car barely runs
My friend just had SLP headers and a Catco cat and a Flowmaster American Thunder installed on his Camaro he takes to shows.
Here is the problem.
When he picked his car up yesterday late, and then started driving home, his engine was running terrible. It runs like "it is on two cylinders". It will barely go up hills. It shakes and vibrates.
I bet him that the shop fried the computer. They ended up having to replace the temperature sensor and several other hoses, etc. during the job.
What do you think they did to introduce the problem?
What do you think the most likely problem is?
Here is the problem.
When he picked his car up yesterday late, and then started driving home, his engine was running terrible. It runs like "it is on two cylinders". It will barely go up hills. It shakes and vibrates.
I bet him that the shop fried the computer. They ended up having to replace the temperature sensor and several other hoses, etc. during the job.
What do you think they did to introduce the problem?
What do you think the most likely problem is?
#3
Member
Join Date: Oct 2001
Location: Broken Arrow, OK (Tulsa)
Posts: 134
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1990 Iroc-Z
Engine: 350 L31 Vortec
Transmission: 700R4
Ouch.. sucks.. i try to never let someone touch my car.. certified or not.. etc... Headers intstall is pretty easy task.. the only hard part is the back passenger side plugs and wires to reinstall.. I can almost bet the plugs and wires are screwed somewhere.. hook up a timeing light and make sure everything is fireing.
#4
Member
iTrader: (3)
Join Date: May 2002
Location: Huntington, Wv
Posts: 161
Likes: 0
Received 0 Likes
on
0 Posts
Make sure the wires are hooked up in the correct firing order too. Since they put headers on they definitely had all the wires off. That would make the car run on only a few cylinders. Check it out.
#5
Supreme Member
Join Date: Jan 2002
Location: Las Vegas, NV
Posts: 1,370
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1990 Iroc-Z
Engine: L98
Transmission: 700R4
SES light come on? If it isn't plug wires then I would start looking for vacuum hoses that need re-connecting.
#6
Senior Member
Join Date: Aug 2001
Location: Memphis, Tn
Posts: 972
Likes: 0
Received 0 Likes
on
0 Posts
Car: 92' RS
Engine: 357
Transmission: TH350
Axle/Gears: 4.10
LOL, i wouldnt even worry about finding the problem. I'd take it back and get it fixed or get me lawyer. my 2 cent
#7
Member
Join Date: Feb 2003
Location: Denison and Ames, Iowa
Posts: 178
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1990 Formula 350
Engine: 5.7
Transmission: 700R4
a lot of the wires might be one but if you jst put on headers they could be burnt from running it before the shop tied them up or put on soom wire looms..i say check the ohms for the wires first....
Thread
Thread Starter
Forum
Replies
Last Post
86IROC112
Engine/Drivetrain/Suspension Parts for Sale
4
08-17-2015 02:00 PM
1992 Trans Am
Engine/Drivetrain/Suspension Parts for Sale
1
08-08-2015 08:16 PM