Best Cowl hoods
#3
Supreme Member
iTrader: (25)
Join Date: Feb 2006
Location: Manteca,California. Nor Cal.
Posts: 7,260
Likes: 0
Received 5 Likes
on
5 Posts
Car: SOLD IT. Mopar guy only now.
Engine: gone
Transmission: gone
Axle/Gears: gone
Re: Best Cowl hoods
I have a goodmark 2.5 cowl. I love it but it is steel and some prefer the fiberglass. Bolts right on and looks great.
#5
Supreme Member
iTrader: (25)
Join Date: Feb 2006
Location: Manteca,California. Nor Cal.
Posts: 7,260
Likes: 0
Received 5 Likes
on
5 Posts
Car: SOLD IT. Mopar guy only now.
Engine: gone
Transmission: gone
Axle/Gears: gone
Re: Best Cowl hoods
and correction they call it a 2 inch cowl hood. But actually measures about 3 inches at the highest point.
#6
Senior Member
Join Date: Mar 2009
Location: 47798 Germany
Posts: 505
Likes: 0
Received 0 Likes
on
0 Posts
Car: '89 RS camaro 305 TBI
Engine: LO3
Transmission: 700R4
Axle/Gears: yep, has those too (stock)
Re: Best Cowl hoods
I guess if my fiberglass/carbonfibre hood attempt fails I´ll definately invest my money in the goodmark cowl hood shown here.
For street use I do not see a lot of benefit in full fiberglass hoods. Steel hoods are just more durable for everyday use.
For street use I do not see a lot of benefit in full fiberglass hoods. Steel hoods are just more durable for everyday use.
#7
Supreme Member
iTrader: (25)
Join Date: Feb 2006
Location: Manteca,California. Nor Cal.
Posts: 7,260
Likes: 0
Received 5 Likes
on
5 Posts
Car: SOLD IT. Mopar guy only now.
Engine: gone
Transmission: gone
Axle/Gears: gone
Re: Best Cowl hoods
that's what I was thinking too. And it didn't help that I bought it 2nd hand from someone desperate for money. Sometimes I have good luck!
Trending Topics
#8
Junior Member
Join Date: Oct 2010
Location: Delaware, USA
Posts: 4
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1987 SC Camaro
Engine: 4 bolt main 350 mild cam alum heads
Transmission: 700r4 stock
Axle/Gears: Stock 3.42 rear
Re: Best Cowl hoods
I have a 3inch bolt on fiberglass hood made by Harwood. Its light but i had to make a hood prop because the shocks were stressing the hood too much when it was closed. Here's a photo
#9
Member
Re: Best Cowl hoods
I have an Unlimited products fiberglass and it sucks, crooked as hell, unfinished bottom, with a two month wait.
#10
Member
#11
Senior Member
Join Date: Oct 2009
Location: New York
Posts: 525
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1988 Camaro IrocZ
Engine: Holley Stealth Ram 385 Stroker
Transmission: Redline Performance 700r4 Trans
Axle/Gears: Bulletproof 4thGen Ls1 SS Rear 3.73
Re: Best Cowl hoods
whats the weight difference from the 2" steel cowl and the stock Iroc Hood?
I will admit i loved the SS hood and stock iroc Hood.. but That 2" Cowl with the stripes half on and half off looks great. Now i have 3 hoods to decide over
I will admit i loved the SS hood and stock iroc Hood.. but That 2" Cowl with the stripes half on and half off looks great. Now i have 3 hoods to decide over
#12
Supreme Member
iTrader: (25)
Join Date: Feb 2006
Location: Manteca,California. Nor Cal.
Posts: 7,260
Likes: 0
Received 5 Likes
on
5 Posts
Car: SOLD IT. Mopar guy only now.
Engine: gone
Transmission: gone
Axle/Gears: gone
Re: Best Cowl hoods
over a stock iroc hood? it is minimal weight difference. this hood is only a few pounds more than a stock rs hood for sure. I love it.
Thread
Thread Starter
Forum
Replies
Last Post
91TTOPZ
Exterior Parts for Sale
5
09-20-2016 12:42 PM