need to put more gauges in...where to put them?
Thread Starter
Joined: Jun 2002
Posts: 13,576
Likes: 30
From: Harford County, MD
Car: camaro sportcoupe
Engine: 7.0L
Transmission: G-Force GF5R
Axle/Gears: Moser 9"
need to put more gauges in...where to put them?
alright guys, i need to put an air/fuel ratio guage and a vacuum/boost gauge. where should i put them and have it look like a good install? i would like to keep my stock cluster intact if possible. here's a pic to show where i am at right now...
Moderator
Joined: Jan 2000
Posts: 20,981
Likes: 11
From: Mercedes Norte, Heredia, Costa Rica
Car: 1984 Z28 Hardtop
Engine: 383 Carb
Transmission: 4L60
Axle/Gears: 3.54 Dana 44
This wouldn't work so well with the the tach where it is now though.
<img src="http://members.shaw.ca/crussel/camaro5.jpg">
<img src="http://members.shaw.ca/crussel/camaro5.jpg">
Supreme Member
Joined: Jun 2003
Posts: 1,985
Likes: 1
From: Massachusetts
Car: candy blue 85 z28
Engine: 305 tpi LB9
Transmission: 700r4 crazy beefed up one
Axle/Gears: ones with teeth
depends if you don;t need to loook at em al the time i would go with the center console where the window switched go, or hanging on the undersise of the dash next to the radios like in front of the passenger but angled to driver. but you may need to fab up something to close the back so it looks clean.
Trending Topics
Junior Member
Joined: May 2004
Posts: 88
Likes: 0
From: North Carolina
Car: 88 IROC-Z
Engine: L98 350
Transmission: 700r4
Try the air conditioner vents...right about your tach. If you can figure out a way to make that work that would be a pretty good spot and you could see them well if you angled them.
If you were willing to move the Tach then you could run the three guages under the A/C vents like my 91 Z (pic here). Maybe disassemble the cluster, remove the stock Tach, and install the aftermarket one in the same space?
Thread Starter
Joined: Jun 2002
Posts: 13,576
Likes: 30
From: Harford County, MD
Car: camaro sportcoupe
Engine: 7.0L
Transmission: G-Force GF5R
Axle/Gears: Moser 9"
well, i don't have a stock tach, iv'e got the cluster with the big gas gauge. i guess i really don't need to look at them all the time. i thought about in the ashtray, i had my water temp and voltage gauges there for a while, but then i put it back to stock. i even have the angle rings to put them there, and the piece of aluminum that i used to fix them in place. putting them in the air vents would require modification to the vents themselves, the gauges are just too big in diameter. anyone got pics of clean installs of gauges in unique places. a non clean install is not an option.
Thread Starter
Joined: Jun 2002
Posts: 13,576
Likes: 30
From: Harford County, MD
Car: camaro sportcoupe
Engine: 7.0L
Transmission: G-Force GF5R
Axle/Gears: Moser 9"
here is an old setup in my old car, it required extensive modification to work though, i would like to avoid this as i currently have switches in the place of the gauges in this pic.
Joined: Nov 2002
Posts: 3,466
Likes: 5
From: MA, USA
Car: 83 bird
Engine: 305/383
Transmission: WC T5
Axle/Gears: 3:42
Originally posted by Air_Adam
My oil pressure guage.
My oil pressure guage.
(no not using this as an excuse to show my new halos off
) Supreme Member
iTrader: (33)
Joined: Jul 2000
Posts: 5,945
Likes: 1
From: Boosted Land
Car: 92 Z28
Engine: Boosted LSX
Thread
Thread Starter
Forum
Replies
Last Post
86IROC112
Engine/Drivetrain/Suspension Parts for Sale
4
Aug 17, 2015 02:00 PM
db057
TBI
10
Aug 11, 2015 10:11 PM





I've got the same stereo deck in my 87 Formula 