parting 1991 z28
Thread Starter
Member
iTrader: (4)
Joined: Aug 2005
Posts: 326
Likes: 1
From: edmonton alberta canada
Car: 91 rs,1 92 rs,92 b4c/1le
Engine: 5.0tbi,5.7 tune port/5.0tpi
Transmission: 5spdx2 and t56
Axle/Gears: 3.08,3.73,3.42
parting 1991 z28
just got a 91 z28 has nice shape grey interior t-top car only drivers seat worn,ground effects are gone,but high rise still there,nice shape black hood with blisters also new in package owners manual,700 r4 trans supposed bullet proof rebuild 0km on that let me know what you need
Thread Starter
Member
iTrader: (4)
Joined: Aug 2005
Posts: 326
Likes: 1
From: edmonton alberta canada
Car: 91 rs,1 92 rs,92 b4c/1le
Engine: 5.0tbi,5.7 tune port/5.0tpi
Transmission: 5spdx2 and t56
Axle/Gears: 3.08,3.73,3.42
Re: parting 1991 z28
Door is good fender not sure on some
Light rust have not taken the ground effect off yet will have a better look
Light rust have not taken the ground effect off yet will have a better look
Member
Joined: May 2010
Posts: 379
Likes: 0
From: O'hare
Car: 91 Z28
Engine: Enhanced 5.0L
Transmission: 700R4
Axle/Gears: 3:42 Posi
Re: parting 1991 z28
looking for the rubber gaskets under the high rise spoiler.....
hood emblem...
hood emblem...
Last edited by zero13; Jul 7, 2014 at 07:53 PM.
Member
Joined: Jan 2003
Posts: 212
Likes: 0
From: Calgary
Car: 1987 IROC
Engine: 383SR
Transmission: 700r4
Axle/Gears: 3.23
Trending Topics
Member
iTrader: (2)
Joined: Feb 2010
Posts: 460
Likes: 3
Car: '89 Camaro
Engine: LS1
Transmission: 4L65/70E
Axle/Gears: 9 Inch, 3.70 gears
Re: parting 1991 z28
I'm looking for a fog light switch and whatever is needed to put it in the dash. Mine doesn't have fog lights, but I'm looking for a discrete switch to arm a nitrous system.
Thread Starter
Member
iTrader: (4)
Joined: Aug 2005
Posts: 326
Likes: 1
From: edmonton alberta canada
Car: 91 rs,1 92 rs,92 b4c/1le
Engine: 5.0tbi,5.7 tune port/5.0tpi
Transmission: 5spdx2 and t56
Axle/Gears: 3.08,3.73,3.42
Re: parting 1991 z28
should have the hatch pull down,i may have fog lights but the switch is white print
Member
iTrader: (2)
Joined: Feb 2010
Posts: 460
Likes: 3
Car: '89 Camaro
Engine: LS1
Transmission: 4L65/70E
Axle/Gears: 9 Inch, 3.70 gears
Re: parting 1991 z28
The print on the switch is not important. Mostly just need the switch and the cover that screws into the dash, or however else it's held into the dash.
Thread Starter
Member
iTrader: (4)
Joined: Aug 2005
Posts: 326
Likes: 1
From: edmonton alberta canada
Car: 91 rs,1 92 rs,92 b4c/1le
Engine: 5.0tbi,5.7 tune port/5.0tpi
Transmission: 5spdx2 and t56
Axle/Gears: 3.08,3.73,3.42
Re: parting 1991 z28
sorry for delay car is gone
Thread
Thread Starter
Forum
Replies
Last Post
CarGuyDennis
Organized Drag Racing and Autocross
137
Dec 6, 2016 11:02 PM
sailtexas186548
Exterior Parts for Sale
14
Feb 29, 2016 08:40 AM







