Cooling Discuss all of the aspects of cooling that you can think of! Radiators, transmissions, electric fans, etc.

need all the bolts for dual fans

Thread Tools
 
Search this Thread
 
Old Apr 17, 2004 | 02:32 PM
  #1  
Trans_AM_88's Avatar
Thread Starter
Senior Member
 
Joined: Feb 2003
Posts: 847
Likes: 0
From: NJ fo0
Car: 1986/88 Frankenstein Trans Am
Engine: carbed L98
Transmission: T-5
need all the bolts for dual fans

hey guys. i need every single bolt needed to mount dual electric fans to the car...top rad support, bottom support and the 3 bolts for each fan. can anyone direct me as to where i can get these bolts? i have no clue where to start.
Reply
Old Apr 18, 2004 | 02:16 PM
  #2  
Z28ricer's Avatar
Supreme Member
iTrader: (2)
 
Joined: Jan 2001
Posts: 4,149
Likes: 3
From: Tampa, FL, USA
Car: 93 240SX
Engine: LQ9
Transmission: T56
Axle/Gears: 3.54 R200 IRS
Go to a junkyard and steal all the bolts from 2 single fan cars.
Reply
Old Apr 18, 2004 | 05:10 PM
  #3  
Trans_AM_88's Avatar
Thread Starter
Senior Member
 
Joined: Feb 2003
Posts: 847
Likes: 0
From: NJ fo0
Car: 1986/88 Frankenstein Trans Am
Engine: carbed L98
Transmission: T-5
i really havent seen any electric fan cars in the junkyards around my area...and if i do theyre already gone
Reply
Old Apr 19, 2004 | 12:29 PM
  #4  
Trans_AM_88's Avatar
Thread Starter
Senior Member
 
Joined: Feb 2003
Posts: 847
Likes: 0
From: NJ fo0
Car: 1986/88 Frankenstein Trans Am
Engine: carbed L98
Transmission: T-5
anywhere else i can look? also...im not sure if i have all the pieces. all i have right now are the 2 fans, top support and the bottom piece. is that all i need?
Reply
Old May 30, 2004 | 02:54 PM
  #5  
CamaroBoy88's Avatar
Junior Member
 
Joined: Jan 2002
Posts: 18
Likes: 0
From: Frankfort, IN
You can just go to a hardware store. The three bolts holding on each fan are M8-1.25 x 25mm, you'll also want to pick up washers for each bolt. As for the plastic piece at the bottom that the fans bolt to, I just used two bolts and nuts I had laying around the garage.
Reply
Old May 30, 2004 | 07:59 PM
  #6  
thirdgen88's Avatar
Supreme Member
20 Year Member
 
Joined: Apr 2003
Posts: 1,751
Likes: 4
From: Bonner Springs, KS
Car: 1995 Corvette
Engine: LT1
Transmission: 6 spd Manual
Axle/Gears: Dana 44, 3:45:1
You can also use transmission pan bolts (700R4).. They have a little washer built into them and they're the right thread size..
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
IROCZDAVE (88-L98)
Engine/Drivetrain/Suspension Parts for Sale
1
Nov 19, 2015 07:03 AM
krisner89
Cooling
12
Oct 10, 2015 06:03 AM
IROCZDAVE (88-L98)
Engine/Drivetrain/Suspension Parts for Sale
0
Sep 2, 2015 08:49 AM
IROCZDAVE (88-L98)
Engine/Drivetrain/Suspension Parts for Sale
0
Sep 2, 2015 08:43 AM
thefirebirdm@n
Cooling
1
Aug 25, 2015 05:21 PM




All times are GMT -5. The time now is 01:08 AM.