Getting started with Tuner Pro
Thread Starter
Joined: Dec 2012
Posts: 407
Likes: 10
From: Clarksville,TN
Car: 1989 GTA
Engine: 5.7 w/Paxton
Transmission: 700R4
Axle/Gears: 3.27
Getting started with Tuner Pro
I just got my aldlcable today, but am needing a little help setting it up. I am just trying to collect data.
Did not get a driver disk with the cable.
Do I need to DL a definition file or something?
Installed drivers: http://www.ftdichip.com/Drivers/VCP.htm
Device manager shows com4
Thanks for any help.
Did not get a driver disk with the cable.
Do I need to DL a definition file or something?
Installed drivers: http://www.ftdichip.com/Drivers/VCP.htm
Device manager shows com4
Thanks for any help.
Last edited by MrPackstin; Apr 4, 2013 at 10:37 PM.
Re: Getting started with Tuner Pro
You will need a bin definition file. And a datstream def file. I believe they are available on TP website.
http://www.tunerpro.net/downloadBinDefs.htm
http://www.tunerpro.net/gmOBDI.htm
or here http://gearhead-efi.com/gearhead-efi/
http://www.tunerpro.net/downloadBinDefs.htm
http://www.tunerpro.net/gmOBDI.htm
or here http://gearhead-efi.com/gearhead-efi/
Last edited by Ronny; Apr 5, 2013 at 10:54 AM.
Thread Starter
Joined: Dec 2012
Posts: 407
Likes: 10
From: Clarksville,TN
Car: 1989 GTA
Engine: 5.7 w/Paxton
Transmission: 700R4
Axle/Gears: 3.27
Re: Getting started with Tuner Pro
TY for the reply. DL'ed both files then loaded the .XDF, but where am I supposed to load the .ads file? Just trying to get live data at this point.
Do I need a 10K resistor? across A and B on an '89 165ecm?
Is it possible to acquire data with TP free? In the help section it states it is only available with RT.
Do I need a 10K resistor? across A and B on an '89 165ecm?
Is it possible to acquire data with TP free? In the help section it states it is only available with RT.
Last edited by MrPackstin; Apr 10, 2013 at 05:39 PM.
Joined: Jun 2000
Posts: 5,364
Likes: 51
From: Enschede, Netherlands
Car: 82 TA 87 IZ L98 88 IZ LB9 88 IZ L98
Engine: 5.7TBI 5,7TPI 5.0TPI, 5,7TPI
Transmission: T5, 700R4, T5, 700R4
Axle/Gears: 3.08, 3.27, 3.45, 3.27
Re: Getting started with Tuner Pro
TY for the reply. DL'ed both files then loaded the .XDF, but where am I supposed to load the .ads file? Just trying to get live data at this point.
Do I need a 10K resistor? across A and B on an '89 165ecm?
Is it possible to acquire data with TP free? In the help section it states it is only available with RT.
Do I need a 10K resistor? across A and B on an '89 165ecm?
Is it possible to acquire data with TP free? In the help section it states it is only available with RT.
as for the ads, you need to go to aquisition->import definition from ads file (adx file is loaded w/ the load definition file selection)
Thread
Thread Starter
Forum
Replies
Last Post
LT1Formula
Engine/Drivetrain/Suspension Parts for Sale
7
Aug 20, 2015 09:36 PM
Dialed_In
Firebirds for Sale
2
Aug 20, 2015 01:45 PM
