Has anybody gotten DIS or CNP on a v8 working using only GM parts?
Thread Starter
Senior Member
Joined: Oct 1999
Posts: 6,621
Likes: 2
Car: 91 Red Sled
Axle/Gears: 10bolt Richmond 3.73 Torsen
Has anybody gotten DIS or CNP on a v8 working using only GM parts?
Title says it all.
I just see a lot of talk and very small steps. This is NOT me asking for a hand out but it seems to me that there has to be somebody holding back. If they are and don't want to share their info than fine but please tell me you've got it working
. A few hints might also be nice.
I just see a lot of talk and very small steps. This is NOT me asking for a hand out but it seems to me that there has to be somebody holding back. If they are and don't want to share their info than fine but please tell me you've got it working
. A few hints might also be nice. 
Supreme Member
Joined: Feb 2000
Posts: 1,416
Likes: 0
From: Johnstown, Ohio
Car: 84 Z28
Engine: 355 (fastburn heads, LT4 HOT cam)
Transmission: 700R4
Axle/Gears: 9-bolt, 3.27
Re: Has anybody gotten DIS or CNP on a v8 working using only GM parts?
Originally posted by JPrevost
Title says it all.
I just see a lot of talk and very small steps. This is NOT me asking for a hand out but it seems to me that there has to be somebody holding back. If they are and don't want to share their info than fine but please tell me you've got it working . A few hints might also be nice.
Title says it all.
I just see a lot of talk and very small steps. This is NOT me asking for a hand out but it seems to me that there has to be somebody holding back. If they are and don't want to share their info than fine but please tell me you've got it working
. A few hints might also be nice. I'm also trying to get the parts in line to finally get the Camaro converted to EFI. I'm looking for a TBI harness. Anyone have one laying around?
EDIT: My design will need a couple non GM parts to be fabbed, but that's pretty much a given anyway.....
Thread Starter
Senior Member
Joined: Oct 1999
Posts: 6,621
Likes: 2
Car: 91 Red Sled
Axle/Gears: 10bolt Richmond 3.73 Torsen
Jud, if I had a harness I'd send it your way.
Funny, as soon as I posted this I found;
https://www.thirdgen.org/techbb2/sho...hreadid=239672
But that's not going to be DIY
.
Funny, as soon as I posted this I found;
https://www.thirdgen.org/techbb2/sho...hreadid=239672
But that's not going to be DIY
. 
TGO Supporter
Joined: Aug 2001
Posts: 1,008
Likes: 0
From: NJ/PA
Car: Yes
Engine: Many
Transmission: Quite a few
check out this thread, it has morphed into the discussion you are looking for.
https://www.thirdgen.org/techbb2/sho...hreadid=279329
https://www.thirdgen.org/techbb2/sho...hreadid=279329
Supreme Member
Joined: Jun 2000
Posts: 7,554
Likes: 1
From: In reality
Car: An Ol Buick
Engine: Vsick
Transmission: Janis Tranny Yank Converter
Re: Has anybody gotten DIS or CNP on a v8 working using only GM parts?
Originally posted by JPrevost
Trending Topics
Thread Starter
Senior Member
Joined: Oct 1999
Posts: 6,621
Likes: 2
Car: 91 Red Sled
Axle/Gears: 10bolt Richmond 3.73 Torsen
Re: Re: Has anybody gotten DIS or CNP on a v8 working using only GM parts?
Originally posted by Grumpy
Yep, lots of the new GM cars/ trucks are using all GM DIS or CNP systems. Matter of fact rumor has it they all do.
Yep, lots of the new GM cars/ trucks are using all GM DIS or CNP systems. Matter of fact rumor has it they all do.
you don't say! Well why the heck are we futsin around with this old junk? How about OBD-I v8 DIS using an f-body ecm. 
Thread
Thread Starter
Forum
Replies
Last Post
