brake light
Thread Starter
Supreme Member
Joined: Jan 2011
Posts: 1,932
Likes: 9
From: Lynden WA
Car: 84 Trans Am, 84 Fiero, 86 944
Engine: 5.0, 2.5, 2.5
Transmission: 5spd
brake light
not the one on the back of the car, the one on the dash, i always set my handbrake when i park, but lately after i release it, light stays on 
i imagine the little prong the plug...... plugs on to is broken off, anyone got a fix, messed with it a bit, thing is touchy as all hell
i imagine the little prong the plug...... plugs on to is broken off, anyone got a fix, messed with it a bit, thing is touchy as all hell 
Member
Joined: Dec 2010
Posts: 334
Likes: 0
From: Near Wichita Ks
Car: 1997 K1500 SS/SB
Engine: LT1 with TPI on top
Transmission: 4L60E/np241,
Axle/Gears: 3.73
Re: brake light
not the one on the back of the car, the one on the dash, i always set my handbrake when i park, but lately after i release it, light stays on i imagine the little prong the plug...... plugs on to is broken off, anyone got a fix, messed with it a bit, thing is touchy as all hell
i imagine the little prong the plug...... plugs on to is broken off, anyone got a fix, messed with it a bit, thing is touchy as all hellpictures ???
Supreme Member
Joined: Jan 2006
Posts: 3,341
Likes: 10
From: Mooresville NC
Car: LOWERED ♦ CRIMSON METALFLAKE
Engine: ► 400 KUBES ◄
Transmission: 765R4
Axle/Gears: EATON POSI 4.56
Them’s The Brakes
Yes it might be broken off allowing it to touch the body ground.
Replace the switch.
◙◙◙◙◙◙◙◙◙◙◙◙◙◙◙
Happy Racing!
◙◙◙◙◙◙◙◙◙◙◙◙◙◙◙
Rule Number 1 Is To Know Which Rules You Can Break
Replace the switch.
◙◙◙◙◙◙◙◙◙◙◙◙◙◙◙
Happy Racing!
◙◙◙◙◙◙◙◙◙◙◙◙◙◙◙
Rule Number 1 Is To Know Which Rules You Can Break
Thread Starter
Supreme Member
Joined: Jan 2011
Posts: 1,932
Likes: 9
From: Lynden WA
Car: 84 Trans Am, 84 Fiero, 86 944
Engine: 5.0, 2.5, 2.5
Transmission: 5spd
Re: brake light
switch? its a little tab on the lever with a plug on it no? and my trans tunnel is carpeted how would it ground out? pics? of the brake light on the dash? im just gonna un plug it, hell i don't need it i know when i set the brake haha
Joined: Dec 2005
Posts: 4,795
Likes: 15
From: St. Cloud, MN
Car: 1984 Trans Am
Engine: LS1383 in work
Transmission: Magnum F - to be installed
Axle/Gears: Zexel Torsen 3.73, 28-spline mosers
Re: brake light
not the one on the back of the car, the one on the dash, i always set my handbrake when i park, but lately after i release it, light stays on i imagine the little prong the plug...... plugs on to is broken off, anyone got a fix, messed with it a bit, thing is touchy as all hell
i imagine the little prong the plug...... plugs on to is broken off, anyone got a fix, messed with it a bit, thing is touchy as all hell Supreme Member
Joined: Jan 2006
Posts: 3,341
Likes: 10
From: Mooresville NC
Car: LOWERED ♦ CRIMSON METALFLAKE
Engine: ► 400 KUBES ◄
Transmission: 765R4
Axle/Gears: EATON POSI 4.56
Them’s The Brakes
Originally Posted by Ozz1967
I have a bad valve, leaky lines or some other issue that caused my "brake light" to stay on in the dash.
Also it doesn’t always come out of the fitting end.
◙◙◙◙◙◙◙◙◙◙◙◙◙◙◙
Happy Racing!
◙◙◙◙◙◙◙◙◙◙◙◙◙◙◙
Slamming The Wall Is Not The Neatest Way To Remove An Engine
Joined: Dec 2005
Posts: 4,795
Likes: 15
From: St. Cloud, MN
Car: 1984 Trans Am
Engine: LS1383 in work
Transmission: Magnum F - to be installed
Axle/Gears: Zexel Torsen 3.73, 28-spline mosers
Re: Them’s The Brakes
You might be losing it in the rear drums, if equipped, and it will look dry because of the small amount, and the camouflage of brake dust.
Also it doesn’t always come out of the fitting end.
◙◙◙◙◙◙◙◙◙◙◙◙◙◙◙
Happy Racing!
◙◙◙◙◙◙◙◙◙◙◙◙◙◙◙
Slamming The Wall Is Not The Neatest Way To Remove An Engine
Also it doesn’t always come out of the fitting end.
◙◙◙◙◙◙◙◙◙◙◙◙◙◙◙
Happy Racing!
◙◙◙◙◙◙◙◙◙◙◙◙◙◙◙
Slamming The Wall Is Not The Neatest Way To Remove An Engine
Thread
Thread Starter
Forum
Replies
Last Post