Building a 383 so Im swapping to carb. Heres a list of stuff Ive got left over. All of the engine parts were removed from a very low mile 97 350 vortec. I will post pics upon request. I am located near Charlotte NC, I prefer local p/u but will ship.

TPI base (has center holes slotted for use on later style heads), runners, plenum, throttle body (w/ sensors), fuel rails w/ holley AFPR, 86 model for coldstart injector and 22lb injectors - $275 obo

TPI harness (decent shape, not cut up or anything, has new MAF pigtail) - $60 obo

TPI 7165 ecm - has a 88 350 memcal (AUJP?) and a motes G1 with prom chip and zif socket - $75 obo

TPI air box w/ k&n filters - $50 obo

350 ESC module (brand new GM, ran for 3k) - $50 obo

Stock MAF - works great - make offer

tpi exhaust manifolds - great shape - make offer

emissions stuff - smog pump, vapor canister, egr valve, egr solenoid, etc - make offer

062 vortec heads - 30-40k, no cracks, drilled for standard intake, great shape - $250 obo

Stock roller lifters, pushrods, timing set, and rockers - make offer

Comp magnum roller tip rockers (1.52 ratio, longslot) w/ ***** and nuts - $90 obo

1 pc rms stock crank - std journals, needs to be polished - $80 obo (prefer local p/u but may ship)

8 Powder Metal rods w/ 350 vortec pistons - $80 obo (will make deal on rods, pistons and crank)

305 motor, rebuilt about 2 yrs ago and has been sitting, 10/10 crank, PM rods, flattop pistons, 10.5:1 comp, 52cc heads new valve job 1.94/1.50 stainless +.100" valves, isky 270/280 mega cam (dur 221/232, .465/.485 lift, 112 lsa), anti pump up lifters, melling m55hv oil pump and steel shaft, melling double roller timing chain, edelbrock performer intake -
I built this for a friend who never paid me and have well over $1000 into it, I would like to get $500 obo (no shipping unless you arrange it)


I think thats about it, I am open to all trades, heres a few things I need,
3 port return style regulator (4-9 psi), 700cfm and larger performance carbs, single plane intakes, y pipe for hooker long tubes, MSD boxes, t-5 pro 5.0 shifter, etc

Thanks for looking
Seth

How much for the tpi harness shipped to 32726?

PM sent

How much for the heads to 80127? (vortec)

pm sent

Bump, make me some offers. PM me for pics, I also will trade for 10 bolt posi units, gears, or whole rears

Seth

TTT, make some offers, and all trades considered

Seth

Bump, deal pending on vortec heads. Make offers on the rest.
I also have the following
Edelbrock 600cfm Elec Choke - $100 obo
Edelbrock Performer intake - $75 obo
TPI large cap HEI distributor - make offer


Seth

would you seperate the tpi air box? I just need the lower peice no filters no top. Thanks

pm sent

BUMP!!!

Hi!

Is the TPI harness sold?

Regards
Olav

TTT, all pms replied to.

Seth

Bump, all offers will be considered. Need to get this stuff gone, I have no room for it.

Seth

Large Cap HEI's are non CC, right? So how can you have a large cap HEI if it's a TPI unit?

Yes they made a large cap CC distributor, they came in all kinda stuff, malibus, caprices, trucks, and on 86 tpi setups.

Bump for the rest, make some offers.

Seth

I will take the TPI air box w/ k&n filters . How much to ship to gordonsville Va 22942?

PM Sent.

Vortec Heads -SOLD
TPI Air Box w/ KN filters - SOLD
MAF - SOLD
Vapor Canister - GONE

Did you get my PM regarding harness ?

Olav