B&M Console Megashifter - Used – the thread on the stick is almost completely stripped - $75
350 block 2 piece rms, 4 bolt mains high nickel casting $100
LT1 Dual fan setup $40
(2) swing out kits NIB $40
Hypertech TPI ignition coil Used for less than 3k miles $30
Aeromotive universal fuel sump NIB $100

SOLD Spohn torque arm with t56 cross member mount- Used - spherical rod end and front drive shaft loop - $250
SOLD New Random Technologies transmission mount torque arm - $200
SOLD New weld in control arm relocation brackets - $45
SOLD Front control arms with new poly bushings and ball joints. Sand blasted and painted gloss black. $100
SOLD Used 2 inch lowering springs $100
SOLD LT1 PBR Brake setup $150

All prices do not include shipping. Parts are located in Frederick MD but I am back and forth between there and Knoxville, TN - Pick-up welcome.
Pictures can be found at http://good-times.webshots.com/album...swSGH?start=24
Thanks

 

you selling that tpi strut tower brace?

 

Was the engine running when pulled? Whats the story behind it?
Millage?

 

DrewsCam - The STB was sold a while back.

Gawboots - The block is from a '70s pickup - It was hot tanked and magnafluxed. It is ready to be machined and rebuilt. I bought the block about 5 years ago so I don't know anything else about it's history.

 

TTT

 

TTT offers?

 

What is the best deal that you could give me on the Megashifter shipped to 91406?
Is it repairable, or does it need a new rod?

Thanks,
Dave

 

Would you sell just the spohn torque arm without the crossmember?

 

PM sent.

 

How much for aluminum DS?

 

drb930 - The **** screws on but will it does not have enough thread left on the rod to keep it from spinning. If I was keeping my car an auto, I would drill through the bottom of the handle into the rod, tap them both, and use a small bolt to lock it in place. There are other ways it can be done and you can also buy short or tall rods from B&M.

I would do 130 shipped.

gregsz-28 - I do not want to split up the torque arm and crossmember. I don't think I can sell the crossmember on its own.

BrOdBaNd - The DS is sold.

 

TTT

 

Want to split up that TA and crossmember yet???

 

gregsz-28 - You can make an offer

 

PM sent

 

Replied. Lower prices and additional items included.

Thanks

 

still have the lowering springs

 

Here are all of the springs that I have:

the ones for $100 + shipping are made by dropzone. I had them on my 86 for about 6 months before I parted it.

I have a brand new eibach pro-kit I would sell for $200 + shipping.

I also have a set of intrax front springs that I would sell for $60 + shipping. I had these on my iroc with chopped rear springs.

 

for the brakes r they front or back
?

 

TTT I have updated all of the items that are sold and lowered the prices on everything remaining.

Thanks

 

pm sent.

 

How much for the power steering pump bracket from the end of page 2?

 

Torque arm...

Standard Duty?
Pro Series?
T-56 from a 93-97 F-Body?
LSx Swap T-56?
Mild Steel?
Chrome moly?
Stock 10 bolt?
9 inch?
12 bolt?
Other?

Might as well throw color in there...

 

racing geek - I would have to find where put all od the accessories I need to part out lbp and an lt1 I have.

Standard Duty
T-56 from a 93-97 F-Body
Mild Steel
It will work with the stock or after market rear end with the factory style through bolt mount.
spherical rod end
front driveshaft loop
Red power coat

There is a link with pictures in the first post.

 

TTT

 

what would you take for the ta is it a firm price?

 

I am firm on the price. I have already lowered it twice. Thanks

 

TTT lower prices and more items

 

Is the spohn torque arm still available? I will give you $250 shipped for it.

 

I am firm on $250+ shipping. Thanks