SOLD



I am selling my complete LT1 T56 swap kit. Trans was removed from a 97 TA in 01 with 40K miles on it. I might have put at the most 10K more miles on it. It shifts perfect. Spec Stage 3 clutch with 10K miles on it. GM slave cyliner with 10K miles on it. Here is a list of what is included:

T56 with bellhousing, flywheel cover and shifter assembly (has a Lou's short stick on it)
SLP billet LT1 flywheel( bolts included)
slave cylinder assembly
T5 pedals (if needed)
manual shifter plate with boot (if needed)
Energy Suspension poly trans mount.
all needed electrical pigtails on trans to wire it up.(reverse, speedo, CAGS)

Trans was dusty and dirty from just sitting in the car and not being driven on the road in 3 years but I just cleaned it up and it looks nice. It is already on a pallet and ready to be shipped.

It has (had) Redline synthetic fluid in it.It was drained prior to boxing it up. Asking $2200 plus shipping. . This trans is NOT a slosh box!! Shifts PERFECT!! Clutch has some minor wear on it. Flywheel shows a few hot spots but the clutch has never been slipped. This clutch is all or nothing on the street. Its amazing.


Slave cylinder and pedals are still in the car.


Cross member in the picture below is NOT included. I just sold it the other day.

 

If anyone wants a shipping quote then you can look up shipping quotes using the following dimensions.

The tranny is in a box that weighs 150lbs and is 36x15x17

Flywheel, bellhousing, clutch, pedals, slave cylinder, shifter weigh 50lbs in a 20x20x20 box.

My zip code is 02790. If will be cheaper to have this stuff shipped to a business address.

If you are seriously interested in this setup then PM me and I will work with you on the total with shipping. Just make sure you give me your zip code so I can look into it on my end before I make or accept offers. The trans is inside a wooden framed crate. It is NOT going anywhere unless someone drops the box off the back of the truck.

 

I will throw this out for anyone who may not need all the parts I have listed here but if you just want the trans, flywheel, clutch, and slave cylinder then PM me and we can figure out a price. I will work with you on shipping charges.

 

would you sell just the clutch i have everything else?

 

$425 shipped. I will include the fairly new GM bolts needed to properly bolt this to a flywheel as well as the alignment tool.

Paypal ID is bottledz28@aol.com. If you dont mind helping me IF you decide to pay then can you please send the money as a gift to a friend so I dont take the 3% hit on the total? It will be about $15 in fees plus the cost of shipping. Im taking a beating here on all these fees. Paypal/Ebay must be rich.

 

Brand new never used set sold on eBay for 355 not too long ago.
Thanks for the offer/info though glws

 

These clutches sell for over $550 new plus shipping. PM me your best offer and I will get back to you.

 

Not particularly interested in the T56 set up, but I live in the same town and was wondering if you had a collection of other third gen parts you might want to part with?

 

90% of all the parts of value are already listed here except for the engine. I have Z06 brakes, LT1 rear brake set, 4th gen posi rear with 3.73s in it. subframe connectors, Spohn lower control arms with adjustable track bar, black SS/ZR1 wheels with almost new Nitto tires on them. What exactly are you looking for?

 

Do you have a lower shift boot?

 

Are you referring to the 5 spd shifter plate? if so then i have this which has the 6 spd logo on it. $75

 

no the one that bolts to the tranny tunnel

 

Its been cut to fit the T56 in my car Other then that its fine. $30 shipped

 

Updated some info guys. Cross member has been sold and therefore I have lowered my price by a few hundred dollars. If you want a bolt in and go kit then this is it. Trans is NOT some unknown part you are getting from a junkyard.

 

Is the engine for sale?

I've been lazily looking for subframe connectors- which product do you have?

 

The engine is for sale but I havent pulled it yet since I dont have a test stand to put it on to run it. The engine is no joke and built with all the best stuff on the shelf. I have just over $10K in the engine in parts and labor. It will put a C6 Z06 to shame .

I have a pair Jegster? bolt in SFC. They can be welded in as well. $100. come pick them up.

 

Bolt in? Fantastic. I'll be back from business travel on Thursday. Would you mind sending me a PM with your number and/or address?

 

If you are referring to the sfc, they are sold

 

Bummer. Thanks for the update.