Do anyone have the part # for a 400sb oil pan that fits TES headers?
Thread Starter
Member
Joined: Feb 2001
Posts: 406
Likes: 0
From: Newark,NJ The state where racing on I 78 rules.
Do anyone have the part # for a 400sb oil pan that fits TES headers?
Hi there
I just found a rebuilt 400 sb for $800 from a local engine shop & I was wondering if anyone has any info ( part #) on a oil pan that will allow for my Edel. TES system to fit under it without touching anything. I made this swap before & the damn oil pan that goes with the stock 400sbc was a little to big & that caused the exhaust to lay right on the oil pan.
Thanx in advanced!
njdaewoo
------------------
86 Tramaro 90% Trans Am/ 10% IROC/Z (nose, hood,& fenders)
Trans Am Mods as of 1/10/01
3inch
T.E.S/Flowmaster setup,gutted cat,gutted maf,relocated mat,373 gears,upgraded factory chip,255 liter h/press. walpro f/pump & throttle body coolant bypass
njdaewoo@excite.com
I just found a rebuilt 400 sb for $800 from a local engine shop & I was wondering if anyone has any info ( part #) on a oil pan that will allow for my Edel. TES system to fit under it without touching anything. I made this swap before & the damn oil pan that goes with the stock 400sbc was a little to big & that caused the exhaust to lay right on the oil pan.
Thanx in advanced!
njdaewoo
------------------
86 Tramaro 90% Trans Am/ 10% IROC/Z (nose, hood,& fenders)
Trans Am Mods as of 1/10/01
3inch
T.E.S/Flowmaster setup,gutted cat,gutted maf,relocated mat,373 gears,upgraded factory chip,255 liter h/press. walpro f/pump & throttle body coolant bypass
njdaewoo@excite.com
TGO Supporter
Joined: Jul 1999
Posts: 607
Likes: 0
How close does it come? I picked up a chromed small block oilpan, and it does not look any different size wise than my 305/350 one...the only difference I can see is the dipstick and internal windage tray.
It would really suck if I put this all together and it didnt fit, so your take on this would be appreciated.
It would really suck if I put this all together and it didnt fit, so your take on this would be appreciated.
Supreme Member
Joined: Jul 1999
Posts: 18,457
Likes: 16
From: Loveland, OH, US
Car: 4
Engine: 6
Transmission: 5
I'm using the old early 70s Z28 pan from GM on the 400 in my 83, with TES currrently; everything fits fine. That pan does require a windage tray however, as it has absolutley no baffles whatsoever. I don't recall the part # off the top of my head as I bought it about 13 years ago.
------------------
"So many Mustangs, so little time..."
ICON Motorsports
------------------
"So many Mustangs, so little time..."
ICON Motorsports
Thread Starter
Member
Joined: Feb 2001
Posts: 406
Likes: 0
From: Newark,NJ The state where racing on I 78 rules.
<font face="Verdana, Arial" size="2">Originally posted by Desert86Roc:
How close does it come? I picked up a chromed small block oilpan, and it does not look any different size wise than my 305/350 one...the only difference I can see is the dipstick and internal windage tray.
It would really suck if I put this all together and it didnt fit, so your take on this would be appreciated.</font>
How close does it come? I picked up a chromed small block oilpan, and it does not look any different size wise than my 305/350 one...the only difference I can see is the dipstick and internal windage tray.
It would really suck if I put this all together and it didnt fit, so your take on this would be appreciated.</font>
Thread
Thread Starter
Forum
Replies
Last Post
Navy8125
Engine/Drivetrain/Suspension Parts for Sale
4
Aug 21, 2015 09:32 AM