V8 Motor Mounts
Thread Starter
Member
Joined: Nov 2009
Posts: 202
Likes: 0
From: Middle of Nowhere, SC
Car: 1984 Camaro Sports Coupe
Engine: 355 chev
Transmission: none at the time
Axle/Gears: stock 10bolt v6 gears
V8 Motor Mounts
I'm getting some progress towards my motor build, so its almost time to start putting stuff back in the motor. So, i need to round up the motor mounts that i need. I've got a 2 piece seal motor 4 bolt main, so its most likely a 80's motor
I'm gonna move the V6 motor mounts up on the K Member, so will these mounts work?
http://cgi.ebay.com/ebaymotors/65-66...Q5fAccessories
Will those bolt up to my motor and my K-member?
Thanks in advance.
Scott
I'm gonna move the V6 motor mounts up on the K Member, so will these mounts work?
http://cgi.ebay.com/ebaymotors/65-66...Q5fAccessories
Will those bolt up to my motor and my K-member?
Thanks in advance.
Scott
Last edited by MrPhotographer0; Feb 24, 2010 at 01:47 PM.
Joined: Mar 2000
Posts: 43,187
Likes: 42
From: Littleton, CO USA
Car: 82 Berlinetta/57 Bel Air
Engine: L92/LQ4 (both w/4" stroke)
Transmission: 4L80E/4L80E
Axle/Gears: 12B-3.73/9"-3.89
No, those aren't the right parts.
Pics of the chassis side are in the V6 to V8 swap sticky.
Pics of the chassis side are in the V6 to V8 swap sticky.
Thread Starter
Member
Joined: Nov 2009
Posts: 202
Likes: 0
From: Middle of Nowhere, SC
Car: 1984 Camaro Sports Coupe
Engine: 355 chev
Transmission: none at the time
Axle/Gears: stock 10bolt v6 gears
Re: V8 Motor Mounts
no i wrote that wrong... will these motor side mount the chassis side mounts?
Joined: Mar 2000
Posts: 43,187
Likes: 42
From: Littleton, CO USA
Car: 82 Berlinetta/57 Bel Air
Engine: L92/LQ4 (both w/4" stroke)
Transmission: 4L80E/4L80E
Axle/Gears: 12B-3.73/9"-3.89
No, those aren't the right parts.
The motor side mounts are stamped steel, no rubber.
The motor side mounts are stamped steel, no rubber.
Joined: Mar 2000
Posts: 43,187
Likes: 42
From: Littleton, CO USA
Car: 82 Berlinetta/57 Bel Air
Engine: L92/LQ4 (both w/4" stroke)
Transmission: 4L80E/4L80E
Axle/Gears: 12B-3.73/9"-3.89
I've been trying to find posts on the topic, finally found an old photo of mine that shows what the mounts look like.
https://www.thirdgen.org/forums/atta...-350-stand.jpg
Both sides look the same. Used on many different GM platforms, including trucks, vans.
https://www.thirdgen.org/forums/atta...-350-stand.jpg
Both sides look the same. Used on many different GM platforms, including trucks, vans.
Thread
Thread Starter
Forum
Replies
Last Post
ambainb
Camaros for Sale
11
Apr 25, 2016 09:21 PM
NBrehm
Engine/Drivetrain/Suspension Parts for Sale
0
Aug 5, 2015 07:57 PM
