got my headers and cat back
Thread Starter
Member
Joined: Jul 2001
Posts: 206
Likes: 0
From: western mass
got my headers and cat back
got my hookers long tubes back from airborne coatings...ohhh they look nice! they fit better in my car than tes or slps too (must just be my gutted engine bay) got my 4" system from mufflex too. man for people who have not seen this system IT IS INTIMIDATING looking at it on the floor! i still start laughing when i look at it on the floor. unfortunately for me my Y pipe does no clear the tranny crossmember. i talked to mufflex and he said it was hooker and a variation in the header design. but he said he would fix or replace the problem free of charge. (very nice guy) it a good thing i dont live across the country from them. although i do live about2-3 hrs away 
and it is a better thing i have an enclosed trailer to bring the car to them 
i absolutely cannot wait to get this in and fire the car for the first time. i am like a kid in the candy shop looking at the 4" system. as soon as i get it all done i will post pics of the exhaust.SICK I TELL YOU!! it is sick!! one good thing the 4" fits nicely over the rear end i may have to bend/lengthen the pan hard rod(the stationary one) but otherwise it fits nicely. think about being behind a z-28 with a single 4" tailpipe.......it looks like exhaust from a school bus!!!
ohhh i cant wait.... just thought i would share my story with you all, thanks for reading and have a great day!!
------------------
87 z28 bowtie aluminum 420small block dry sump crower lt. wt. knife edged crank oliver lt wt rods brodix track 1's super ram intake slp 1 3/4 headers accel dfi art carr 700 r4 3.42 gears ssm sub frame/ladder bars.....other parts on the way ,soon to be finished!! couple more weeks!!!
http://people.ne.mediaone.net/gdm
and it is a better thing i have an enclosed trailer to bring the car to them i absolutely cannot wait to get this in and fire the car for the first time. i am like a kid in the candy shop looking at the 4" system. as soon as i get it all done i will post pics of the exhaust.SICK I TELL YOU!! it is sick!! one good thing the 4" fits nicely over the rear end i may have to bend/lengthen the pan hard rod(the stationary one) but otherwise it fits nicely. think about being behind a z-28 with a single 4" tailpipe.......it looks like exhaust from a school bus!!! ohhh i cant wait.... just thought i would share my story with you all, thanks for reading and have a great day!!
------------------
87 z28 bowtie aluminum 420small block dry sump crower lt. wt. knife edged crank oliver lt wt rods brodix track 1's super ram intake slp 1 3/4 headers accel dfi art carr 700 r4 3.42 gears ssm sub frame/ladder bars.....other parts on the way ,soon to be finished!! couple more weeks!!!
http://people.ne.mediaone.net/gdm
TGO Supporter
iTrader: (2)
Joined: Jul 1999
Posts: 13,579
Likes: 9
From: Readsboro, VT
Car: 85 IROC-Z / 88 GTA
Engine: 403 LSx (Pending) / 355 Tuned Port
Transmission: T56 Magnum (Pending) / T5
Axle/Gears: 3.42 / ?
Where in Western MA are you located? I live in Adams and work in Pittsfield. I'd love to see your car sometime!
------------------
The IROC Homepage
<A HREF="http://www.rit.edu/~jli4307/camaro" TARGET=_blank>
View the restoration of an 85 IROC</A>
Custom Thirdgen Subwoofer Enclosures
"I didn't know a bored out Ford could go so slow" -Shenandoah
------------------
The IROC Homepage
<A HREF="http://www.rit.edu/~jli4307/camaro" TARGET=_blank>
View the restoration of an 85 IROC</A>
Custom Thirdgen Subwoofer Enclosures
"I didn't know a bored out Ford could go so slow" -Shenandoah
Thread Starter
Member
Joined: Jul 2001
Posts: 206
Likes: 0
From: western mass
springfield agawam area. about 30 minutes from pittsfield. hopefully in the next week or two it will be done and i will be taking it to nj to get the exhaust done. otherwise it aint much to look at now...about 3 " of dust from it sitting for 2.5 years , mildew-ish interior and spaghetti mess of wiring. soon enough it will be done though... i cant wait!
------------------
87 z28 bowtie aluminum 420small block dry sump crower lt. wt. knife edged crank oliver lt wt rods brodix track 1's super ram intake slp 1 3/4 headers accel dfi art carr 700 r4 3.42 gears ssm sub frame/ladder bars.....other parts on the way ,soon to be finished!! couple more weeks!!!
http://people.ne.mediaone.net/gdm
------------------
87 z28 bowtie aluminum 420small block dry sump crower lt. wt. knife edged crank oliver lt wt rods brodix track 1's super ram intake slp 1 3/4 headers accel dfi art carr 700 r4 3.42 gears ssm sub frame/ladder bars.....other parts on the way ,soon to be finished!! couple more weeks!!!
http://people.ne.mediaone.net/gdm
Thread
Thread Starter
Forum
Replies
Last Post