B&m shifter wiring, help needed please
#1
Member
Thread Starter
Join Date: Oct 2009
Location: Berwyn, PA
Posts: 134
Likes: 0
Received 0 Likes
on
0 Posts
Car: 91 camaro RS
Engine: 350
Transmission: 700r4
B&m shifter wiring, help needed please
im a little confused with the wiring for the megashifter.
Basically i have three questions
1. should i have power to more than the dark blue wire?
2. with the two switches, it dosent say where or which prongs i should attatch to first. i assumed the lower prongs go to dark blue? the directions say different then the schematic?
3. in the circled area of the schematic do i take a new wire from saftey swith to a2/1 on the relay then ground a1/0 or what?
your help is much apperciaated
rich
Basically i have three questions
1. should i have power to more than the dark blue wire?
2. with the two switches, it dosent say where or which prongs i should attatch to first. i assumed the lower prongs go to dark blue? the directions say different then the schematic?
3. in the circled area of the schematic do i take a new wire from saftey swith to a2/1 on the relay then ground a1/0 or what?
your help is much apperciaated
rich
#3
Senior Member
iTrader: (1)
Join Date: Mar 2009
Location: Stoughton, MA
Posts: 817
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 camaro Z28
Engine: 305 5.0 V8 carburated
Transmission: 700r4
Re: B&m shifter wiring, help needed please
1. I'm not sure about that one.
2. As far as the switches go, it doesn't matter which prong is connected to which wire, as long as the second wire on each switch goes to where it should.
3. Yes, you take a new wire from one of the switches to the coil on the relay ( in this case, that would be A2) and then another new wire from the other end of the coil (A1) to ground.
2. As far as the switches go, it doesn't matter which prong is connected to which wire, as long as the second wire on each switch goes to where it should.
3. Yes, you take a new wire from one of the switches to the coil on the relay ( in this case, that would be A2) and then another new wire from the other end of the coil (A1) to ground.
#5
Member
Join Date: Aug 2010
Location: San Antonio
Posts: 230
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1984 Z28 T-TOP
Engine: 355 Lt1 w/Hotcam
Transmission: TH700R4
Axle/Gears: 3.73 4th gen limited slip
Re: B&m shifter wiring, help needed please
Quick question, did the B&M shifter come with a shift plate? The plate that says P, R, OD, D, 3, 2, 1.
#6
Senior Member
iTrader: (1)
Join Date: Mar 2009
Location: Stoughton, MA
Posts: 817
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 camaro Z28
Engine: 305 5.0 V8 carburated
Transmission: 700r4
Re: B&m shifter wiring, help needed please
Yes it does come with a shift plate, but you must have the original shift plate from the car to mount it to. You cut out a hole in the original plate and then screw the included plate down on top of that.
Thread
Thread Starter
Forum
Replies
Last Post
1992 Trans Am
History / Originality
27
05-10-2023 07:19 PM
NBrehm
Engine/Drivetrain/Suspension Parts for Sale
1
08-25-2015 11:49 PM