ls1 slp headers fit automatic swaps?
Thread Starter
Supreme Member
iTrader: (3)
Joined: Jan 2004
Posts: 2,311
Likes: 0
From: p'cola FL
Car: 88 iroc-z/28
Engine: 408 lsx
Transmission: 5800 stall
Axle/Gears: 4.71
ls1 slp headers fit automatic swaps?
just tossing this out here for conversation.
ive never payed attention to these before, but with the short drivers side header, this looks to be an option to clear an automatic if the tubes cleared the chassis.
the passenger side looks similar to my hawks headers.
anyone tried these before?
i have no idea the part #.
ive never payed attention to these before, but with the short drivers side header, this looks to be an option to clear an automatic if the tubes cleared the chassis.
the passenger side looks similar to my hawks headers.
anyone tried these before?
i have no idea the part #.
Thread Starter
Supreme Member
iTrader: (3)
Joined: Jan 2004
Posts: 2,311
Likes: 0
From: p'cola FL
Car: 88 iroc-z/28
Engine: 408 lsx
Transmission: 5800 stall
Axle/Gears: 4.71
Re: ls1 slp headers fit automatic swaps?
Compare it to 3rd gen SBC headers. The shape isnt even close to fitting
Additionally, the pass header will not fit at all. Noone is going to buy a set of headers just to (maybe) use one side
Additionally, the pass header will not fit at all. Noone is going to buy a set of headers just to (maybe) use one side
Supreme Member
iTrader: (2)
Joined: Dec 2006
Posts: 5,538
Likes: 0
From: Hou. TX
Car: 86 TA, 91 B4C
Engine: 5.3, 4.8
Transmission: 4L80 4000, T56
Axle/Gears: 4.30 M12, 23.42 10 bolt
Re: ls1 slp headers fit automatic swaps?
I am honestly thinking of hacking a set of hooker supercomps i have and making new primaries route into the old pipes...
Trending Topics
Thread Starter
Supreme Member
iTrader: (3)
Joined: Jan 2004
Posts: 2,311
Likes: 0
From: p'cola FL
Car: 88 iroc-z/28
Engine: 408 lsx
Transmission: 5800 stall
Axle/Gears: 4.71
Re: ls1 slp headers fit automatic swaps?
if the passenger side doesnt fit, it doesnt fit, but there are always deals out there to be had, so its good to know what IS possible.
wrecked car, hard landing from a wheelstand, etc.... sometimes parts show up super cheap and its worth grabbing them up.
Supreme Member
iTrader: (2)
Joined: Dec 2006
Posts: 5,538
Likes: 0
From: Hou. TX
Car: 86 TA, 91 B4C
Engine: 5.3, 4.8
Transmission: 4L80 4000, T56
Axle/Gears: 4.30 M12, 23.42 10 bolt
Re: ls1 slp headers fit automatic swaps?
Yea, i am seriously probably going to use my supercomps, will looks like crap but i am not worried about the looks.
Member
iTrader: (1)
Joined: Sep 2008
Posts: 181
Likes: 0
From: NE & KS
Car: 92 Camaro RS
Engine: LS1
Transmission: T56
Axle/Gears: 3.42
Re: ls1 slp headers fit automatic swaps?
are you sure those are ls1 f-body slp headers? Dont look like any of the SLP headers i've ever installed on customer vehicles before.
Joined: Sep 2003
Posts: 25,895
Likes: 429
From: Pittsburgh PA
Car: 89 Iroc-z
Engine: 555 BBC Turbo
Transmission: TH400
Axle/Gears: MWC 9” 3.00
Re: ls1 slp headers fit automatic swaps?
They certainly dont look like my pacesetters for my 99 trans am. Passenger side does but drivers side does not, but i dont remember exactly. Didnt pay too much attention to them.
I know thirdgen headers sweep back further as the Kmember sits pretty much straight down below the middle cylinders
I know thirdgen headers sweep back further as the Kmember sits pretty much straight down below the middle cylinders
Last edited by Orr89RocZ; Jan 5, 2010 at 10:50 AM.
Thread Starter
Supreme Member
iTrader: (3)
Joined: Jan 2004
Posts: 2,311
Likes: 0
From: p'cola FL
Car: 88 iroc-z/28
Engine: 408 lsx
Transmission: 5800 stall
Axle/Gears: 4.71
Re: ls1 slp headers fit automatic swaps?
that is an older version of the slp header. this is the new version, its a tad different.
doubt it fits either.
http://www.slponline.com/view_produc...46&BIG=30046-1
doubt it fits either.
http://www.slponline.com/view_produc...46&BIG=30046-1
Thread
Thread Starter
Forum
Replies
Last Post
NBrehm
Engine/Drivetrain/Suspension Parts for Sale
1
Aug 25, 2015 11:49 PM
