Vortech V4 Z Trim
#1
Junior Member
Thread Starter
Join Date: Nov 2002
Location: Sydney, Australia
Posts: 5
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1960 Pontiac
Engine: 474 Butler Performance
Transmission: T400 Fully Manualised
Vortech V4 Z Trim
G'day,
I was just wondering if any of you guys have had any experiences with the Vortech V4 Z Trim Centrifugal Supercharger???
I'm looking at putting one on an injected 474 Pontiac engine
Gas
I was just wondering if any of you guys have had any experiences with the Vortech V4 Z Trim Centrifugal Supercharger???
I'm looking at putting one on an injected 474 Pontiac engine
Gas
#2
Supreme Member
Join Date: Jul 1999
Location: Indianapolis, IN
Posts: 1,827
Likes: 0
Received 1 Like
on
1 Post
Car: 2000 Trans Am
Engine: LS1
Transmission: T56
That is a BIIIIIIIIG blower. The largest I have ever seen on a thirdgen is one of their XX-Trim blowers. And it took up a **** load of space on the drivers side.
#3
Junior Member
Thread Starter
Join Date: Nov 2002
Location: Sydney, Australia
Posts: 5
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1960 Pontiac
Engine: 474 Butler Performance
Transmission: T400 Fully Manualised
Vortech V4 Z Trim
It will actually go on a 1960 Pontiac...heaps of room in that engine bay. It will use aluminium heads,Victor single plane manifold, twin throttle body setup with large injectors.
Gas
Gas
#5
Senior Member
iTrader: (1)
Join Date: Jul 1999
Location: Cincinnati
Posts: 578
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1987 GTA
Engine: PT88 Turbo DART 406
Transmission: th400
Axle/Gears: 9" ford
I agree with GUIDO...PLUS you will not find too much about those blowers because Vortech JUST released them...Its so now infact they dont have many specs out on it yet.... I doubt if Many/ANY mainstream guys have their hands on one at this point...
That would make some SICK power thats for sure...Id love to have one but am looking more at a YS trim upgrade down the road...
That would make some SICK power thats for sure...Id love to have one but am looking more at a YS trim upgrade down the road...
#6
Junior Member
Thread Starter
Join Date: Nov 2002
Location: Sydney, Australia
Posts: 5
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1960 Pontiac
Engine: 474 Butler Performance
Transmission: T400 Fully Manualised
Yeh,
I know they are only new.
I know that they are pretty huge aswell...That's why I want one!!!!
I'm getting parts from Jim Butler.... everything except the block shipped to Australia. I should be doing that around christmas time. Then I'll be getting it assembled and then work out the fuel injection side of things....then the huffer on the side.
It should be good for 200 or so BHP...hahahaha!!!!!
what sort of injectors would you guys recommend???
You all sound like you are into High Performance.....that's why I'm here!!!
Gas
I know they are only new.
I know that they are pretty huge aswell...That's why I want one!!!!
I'm getting parts from Jim Butler.... everything except the block shipped to Australia. I should be doing that around christmas time. Then I'll be getting it assembled and then work out the fuel injection side of things....then the huffer on the side.
It should be good for 200 or so BHP...hahahaha!!!!!
what sort of injectors would you guys recommend???
You all sound like you are into High Performance.....that's why I'm here!!!
Gas
Thread
Thread Starter
Forum
Replies
Last Post
brettd
Power Adders
2
01-25-2002 12:54 PM