Back from the scale the car is lighter.
Thread Starter
Supreme Member
Joined: Oct 1999
Posts: 1,259
Likes: 1
From: So-cal.
Back from the scale the car is lighter.
I still have the cast iron heads and block in the car.
*** Front rear Total
Old 2020 1420 3440
New 1760 1485 3245
Diff -260 +65 -195
The front to rear split has gone from 600 down to 275
Do you think I can get it to 50 / 50 front - rear
Jerry
*** Front rear Total
Old 2020 1420 3440
New 1760 1485 3245
Diff -260 +65 -195
The front to rear split has gone from 600 down to 275
Do you think I can get it to 50 / 50 front - rear
Jerry
Last edited by JERRYWHO; Jun 16, 2003 at 09:59 PM.
Joined: Mar 2000
Posts: 5,713
Likes: 133
From: Orange, CA
Car: '90 Trans Am-12.45@110.71
Engine: 355 w/AFR 195's Elem. 400/430 HP/TQ
Transmission: Tremec T-56
Axle/Gears: 12 Bolt 3.73
Yep...tub the back, install the Rodeck, some 14.0x32's and get some skinnys for the front.
:lala: :lala: :lala:
Damn, I knew there was some reason I couldn't keep up with ya!
:lala: :lala: :lala:Damn, I knew there was some reason I couldn't keep up with ya!
Last edited by Dyno Don; Jun 16, 2003 at 10:44 PM.
Senior Member
Joined: Feb 2001
Posts: 708
Likes: 48
From: So. Cal
Car: '89 GTA, '15 Camaro LS 6sp.
Engine: L98, LFX.
Transmission: 4L60, AY6.
Axle/Gears: 3.27's.
weighing my truck
Jerry,
Where in Chino did you get it weighed? Is it off the 10?
Do you have to wait in line with the other "big rigs" to get it weighed?
How much of a fee do they typically charge?
As you can tell from all the questions I've never "weighed" a vehicle before.
I'd like to weigh my '88 Toyota std. bed 2WD PU.
-Mike
Where in Chino did you get it weighed? Is it off the 10?
Do you have to wait in line with the other "big rigs" to get it weighed?
How much of a fee do they typically charge?
As you can tell from all the questions I've never "weighed" a vehicle before.
I'd like to weigh my '88 Toyota std. bed 2WD PU.
-Mike
Last edited by Mikos_89; Jun 17, 2003 at 01:52 AM.
Thread Starter
Supreme Member
Joined: Oct 1999
Posts: 1,259
Likes: 1
From: So-cal.
Re: weighing my truck
Originally posted by Mikos_89
Jerry,
Where in Chino did you get it weighed?
-Mike
Jerry,
Where in Chino did you get it weighed?
-Mike
Chino Valley Fuel
5415 Schaefer Ave.
Chino, Ca.91710
909-393-4415
Chino Valley Fuel is a cardlock type gas station with a scale and Never has a line. The hours are 6:00am-5:00pm M-F. The cost is $ 5.00 for front, rear and total.
Jerry
Thread Starter
Supreme Member
Joined: Oct 1999
Posts: 1,259
Likes: 1
From: So-cal.
One more trip to the scales for a update.
*** Front rear Total
Old. 2020 1420 3440
New 1620 1400 3020
Diff.. -400 -20 -420
3020 lbs with a six point roll bar and a big Dana rear.
Jerry
*** Front rear Total
Old. 2020 1420 3440
New 1620 1400 3020
Diff.. -400 -20 -420
3020 lbs with a six point roll bar and a big Dana rear.
Jerry
I am sure that you can get it pretty close if not right down to the once of being 50/50 in weight front/rear 
Thread
Thread Starter
Forum
Replies
Last Post
Ghettobird52
Tech / General Engine
16
Jul 5, 2024 11:18 PM
db057
TBI
10
Aug 11, 2015 10:11 PM