Strut Tower Brace for carbed motor?
Thread Starter
Junior Member
Joined: Feb 2009
Posts: 35
Likes: 0
From: York, NY
Car: 85 z28
Engine: 355 SBC
Transmission: 700R4 w/ shift kit & Corvette Servo
Axle/Gears: 3.08
Strut Tower Brace for carbed motor?
I am interested in buying a strut tower brace however, I am not sure which one to buy due to having a carburetor, i know most are made for tpi setups. Wondering if anyone can toss me a part number or send me in the right direction. I have looked at hawks website and summits and their search engines have yielded me with boggled answers. Thanks.
Supreme Member
Joined: Sep 2002
Posts: 9,192
Likes: 19
From: Cary, North Carolina
Car: 1992 RS
Engine: Carbed 350
Transmission: 700R4
Axle/Gears: 3.42 posi
Re: Strut Tower Brace for carbed motor?
http://www.summitracing.com/parts/EDL-5227/
That's an Edelbrock, what I'm using - but it specifies for A/C on pass side - if you have A/C and it's on driver side, you'll need to look further I guess.
That's an Edelbrock, what I'm using - but it specifies for A/C on pass side - if you have A/C and it's on driver side, you'll need to look further I guess.
Banned
iTrader: (12)
Joined: Jul 1999
Posts: 12,212
Likes: 13
From: Bertram (outside Austin), TX
Car: 87 GTA
Engine: L98
Transmission: 700R4
Axle/Gears: Dana M78 3.27 posi
Re: Strut Tower Brace for carbed motor?
The one for carbs should be the same as the one for TBI cars.
Last edited by Stephen; Jul 6, 2010 at 11:28 PM.
Joined: Aug 1999
Posts: 19,282
Likes: 103
From: Lawrence, KS
Car: Met. Silver 85 IROC/Sold
Engine: 350 HO Deluxe (350ci/330hp)
Transmission: T-5 (Non-WC)
Axle/Gears: Limited Slip 3.23's
Re: Strut Tower Brace for carbed motor?
http://www.summitracing.com/parts/EDL-5227/
That's an Edelbrock, what I'm using - but it specifies for A/C on pass side - if you have A/C and it's on driver side, you'll need to look further I guess.
That's an Edelbrock, what I'm using - but it specifies for A/C on pass side - if you have A/C and it's on driver side, you'll need to look further I guess.
I too am using the above, but I was forced to wait until I swapped in a serp system which moves the compressor to the pass side. If you've eliminated the AC, go for it. Pic in my vbGarage (lower left), should you wish a peek.JamesC
Member
iTrader: (7)
Joined: Sep 2003
Posts: 267
Likes: 0
From: Coupeville, Washington
Car: 1986 IROC T-TOP
Engine: 350
Transmission: 700-R4
Re: Strut Tower Brace for carbed motor?
This one from MAC will work. Can't tell you anything about it though, never used or seen one.
http://www.macperformance.com/store/...Product_ID=444
http://www.macperformance.com/store/...Product_ID=444
Thread
Thread Starter
Forum
Replies
Last Post
ambainb
Camaros for Sale
11
Apr 25, 2016 09:21 PM
NBrehm
Engine/Drivetrain/Suspension Parts for Sale
0
Aug 5, 2015 07:57 PM
