anyone bored the edelbrock TBI manifold to 2"
Thread Starter
Member
Joined: Apr 2000
Posts: 444
Likes: 0
From: Denver, colorado
anyone bored the edelbrock TBI manifold to 2"
I was going to bore the edelbrock TBI manifold from 1 11/16 to 2" but I talked to edelbrock and they said I would Hit the water jackets if I did. I actually want to bore it slightly under 2" (48mm) and wanted to know if anyone had done it.
I gotta run an egr and would prefer to go this route rather than a carb manifold and an adapter.
Anyone know if it can be done cause I wonder if edelbrock is trying to cover their a**.
Thanks....bob
------------------
91 camaro RS L03 convert,
t-5, ultimate TBI mods,TBI spacer,SLP 1 5/8 headers,
3"cat back, 3.42 torsen posi,alston SFC's,Global West LCA relocation brackets, edelbrock STB
I gotta run an egr and would prefer to go this route rather than a carb manifold and an adapter.
Anyone know if it can be done cause I wonder if edelbrock is trying to cover their a**.
Thanks....bob
------------------
91 camaro RS L03 convert,
t-5, ultimate TBI mods,TBI spacer,SLP 1 5/8 headers,
3"cat back, 3.42 torsen posi,alston SFC's,Global West LCA relocation brackets, edelbrock STB
Supreme Member
Joined: Jul 2000
Posts: 1,341
Likes: 0
From: Where the chicks absolutely LOVE the V-8 rumble!
Car: 92 RS - Fully Restored w/Custom Int
Engine: LO3 with some mods
Transmission: T-5
Axle/Gears: 3.42 Richmond
Can't be done...the inside of the throttle bore housing is hollow. the most you might be able to widen it is about 1/8"
------------------
92 Camaro RS LO3, 5-spd, T-tops
Performance:
SLP 1 3/4" Headers (Coated by Paul Barry Motorsports), Flowmaster Catback Exhaust, Fastchip Performance PROM, Centerforce Dual Friction Clutch, Xact 8mm wires, Open Air Element w/K&N Filter, Z28 Grille w/aftmkt fog lamps
Electronics:
Alpine 8030 Alarm System, Valentine One Radar Detector (How did I ever drive without one?), Pioneer DEH 7450 Head Unit w/6-pack CD changer, Pioneer DEQ 7600 Sound Processor, 2 Kenwood KAC-846 Amps powering 2 12" Pro Red subs, 2 Pioneer 6x9 and 2 MTX 4x6 speakers.
NEXT UP: TBI mods, Edelbrock performer intake
------------------
92 Camaro RS LO3, 5-spd, T-tops
Performance:
SLP 1 3/4" Headers (Coated by Paul Barry Motorsports), Flowmaster Catback Exhaust, Fastchip Performance PROM, Centerforce Dual Friction Clutch, Xact 8mm wires, Open Air Element w/K&N Filter, Z28 Grille w/aftmkt fog lamps
Electronics:
Alpine 8030 Alarm System, Valentine One Radar Detector (How did I ever drive without one?), Pioneer DEH 7450 Head Unit w/6-pack CD changer, Pioneer DEQ 7600 Sound Processor, 2 Kenwood KAC-846 Amps powering 2 12" Pro Red subs, 2 Pioneer 6x9 and 2 MTX 4x6 speakers.
NEXT UP: TBI mods, Edelbrock performer intake
Supreme Member
Joined: Jul 1999
Posts: 4,310
Likes: 1
I have a cutaway pic of it. the walls are way too thin.
------------------
-Tas
'89 Formula WS-6
[soon to have Hooker 1-5/8" 50 state legal headers installed]
305, TBI, auto, 14x3 chrome flat based open element with K&N, Milodon 160* thermo, functional Formula hood, cross-flow Flowmaster, '99z28 rear pipes and tips....
Super GRK_Taz World
EFI & Intake Options
AOL IM: superGRtaz
------------------
-Tas
'89 Formula WS-6
[soon to have Hooker 1-5/8" 50 state legal headers installed]
305, TBI, auto, 14x3 chrome flat based open element with K&N, Milodon 160* thermo, functional Formula hood, cross-flow Flowmaster, '99z28 rear pipes and tips....
Super GRK_Taz World
EFI & Intake Options
AOL IM: superGRtaz
Thread Starter
Member
Joined: Apr 2000
Posts: 444
Likes: 0
From: Denver, colorado
Thank you very much guys. I am glad I didn't learn this one the hard way.I understand the old manifolds were 2"bores and they had a tube that went inside the bores that was 1 11/16th. Maybe I can find one of the old ones.
Thanks again on this.....bob
------------------
91 camaro RS L03 convert,
t-5, ultimate TBI mods,TBI spacer,SLP 1 5/8 headers,
3"cat back, 3.42 torsen posi,alston SFC's,Global West LCA relocation brackets, edelbrock STB
Thanks again on this.....bob
------------------
91 camaro RS L03 convert,
t-5, ultimate TBI mods,TBI spacer,SLP 1 5/8 headers,
3"cat back, 3.42 torsen posi,alston SFC's,Global West LCA relocation brackets, edelbrock STB
Thread
Thread Starter
Forum
Replies
Last Post
86IROC112
Engine/Drivetrain/Suspension Parts for Sale
4
Aug 17, 2015 02:00 PM
