Who is running AFR 190 heads???????
Thread Starter
Member
iTrader: (1)
Joined: Jul 1999
Posts: 247
Likes: 1
From: Tucson, Arizona
Car: 1987 IROC Z28
Engine: 6.0L LQ9 crate engine
Transmission: Performa Built 700R4
Axle/Gears: 3.42 10 bolt, Eaton/Moser
Who is running AFR 190 heads???????
I have a set of the AFR 190 straight plug heads. Any of you AFR guys using a shorty spark plug? If so which model? I have a problem with cylinder # 7. It's way too close to the header pipe.
Help!!
------------------
Phil87IROC
Blue '87 IROC, 383 Crate Motor, KB pistons, AFR 190 heads, ZZ-9 cam, Edelbrock RPM intake, Hooker SC/LT headers, Edelbrock 750 cfm Carb (#1411), stock T-5, GM 3.42 rear w/Auburn posi.
Ohio Valley Dragstrip Trophy Bracket WINNER - 8.39 ET on a 1.82 sec. - 60'. Best MPH = 84.44. Still Tuning Carb!
Red '89 IROC L98, TES, 700R4, T-Tops, K&Ns w/open air boxes, 160 T-stat, Hyper Chip, gutted MAF & CAT, Jacobs Ign., 53kv coil, MSD wires.
Help!!
------------------
Phil87IROC
Blue '87 IROC, 383 Crate Motor, KB pistons, AFR 190 heads, ZZ-9 cam, Edelbrock RPM intake, Hooker SC/LT headers, Edelbrock 750 cfm Carb (#1411), stock T-5, GM 3.42 rear w/Auburn posi.
Ohio Valley Dragstrip Trophy Bracket WINNER - 8.39 ET on a 1.82 sec. - 60'. Best MPH = 84.44. Still Tuning Carb!
Red '89 IROC L98, TES, 700R4, T-Tops, K&Ns w/open air boxes, 160 T-stat, Hyper Chip, gutted MAF & CAT, Jacobs Ign., 53kv coil, MSD wires.
Member
Joined: Apr 2000
Posts: 223
Likes: 0
From: Wilmington, IL Age: 35
Phil,
Here is a link to a thread from a couple months ago, check it out. Look at my very first post in the thread about shortening standard plugs. It's what I had to do, and it works out to a gain of about 3/16ths of an inch. Not much of a gain, but better than what you have now.
https://www.thirdgen.org/messgboard/...ML/007318.html
And to answer your question, Accel doesn't make a "shorty" style gasket plug as of yet.....This much I know. And, I'm not yet aware of anyone ELSE that makes a gasketed shorty style plug.
------------------
86 Trans Am WS6 Black with tinted windows, shaved door handles
ZZ4, Mini-ram, true duals, LT4 HotCam, AFR 195 heads.
***Too many other mods to mention***
"In the future, cities will become deserts,
roads will become battlefields, and the hope of mankind
will appear as a stranger" The Road Warrior
Here is a link to a thread from a couple months ago, check it out. Look at my very first post in the thread about shortening standard plugs. It's what I had to do, and it works out to a gain of about 3/16ths of an inch. Not much of a gain, but better than what you have now.
https://www.thirdgen.org/messgboard/...ML/007318.html
And to answer your question, Accel doesn't make a "shorty" style gasket plug as of yet.....This much I know. And, I'm not yet aware of anyone ELSE that makes a gasketed shorty style plug.
------------------
86 Trans Am WS6 Black with tinted windows, shaved door handles
ZZ4, Mini-ram, true duals, LT4 HotCam, AFR 195 heads.
***Too many other mods to mention***
"In the future, cities will become deserts,
roads will become battlefields, and the hope of mankind
will appear as a stranger" The Road Warrior
Thread
Thread Starter
Forum
Replies
Last Post
