Tech / General Engine Is your car making a strange sound or won't start? Thinking of adding power with a new combination? Need other technical information or engine specific advice? Don't see another board for your problem? Post it here!
Sponsored by:
Sponsored by: CARiD

A.I.R, smog pump removal, PHASE I

Thread Tools
 
Search this Thread
 
Old Oct 12, 2001 | 07:31 PM
  #1  
un4givin89's Avatar
Thread Starter
Banned
 
Joined: Jun 2001
Posts: 2,228
Likes: 1
From: Lan Terminal
A.I.R, smog pump removal, PHASE I

Alright, tonight I started the process of removing the smog pump after work. Sadly the sun went down before I could get done. However I am detailing every step with photos and specs and nut sizes, gonna write a slightly more in depth tech then the one on the tech board.

Tomorrow I'm gonna take the pully and belt off and remove the pump itself. And plug the holes on the exhuast maniafold.

One question, will my coolent bypass remain.

------------------
un4givin89

Reply
Old Oct 12, 2001 | 09:44 PM
  #2  
West Coast GTA Man's Avatar
Senior Member
 
Joined: Jun 2001
Posts: 562
Likes: 0
From: New Port Richey, Florida, USA
Car: 1989 Pontiac GTA Hardtop.
Engine: ZZ4 - 350
Transmission: Garbage
Hey man, when you get that article ready, email it to me!
Thanks!
Mike

------------------
Check out My Car Pics http://albums.photo.epson.com/j/Albu...667&a=13599419

Gran Turismo Americano "The Ultimate Firebird"
Smokin 1989 GTA- Bone stock except for exhaust. (no catalytic-stainless pipe into Flowmaster 2 chamber) & AC Delco Rapid Fire Plugs
Reply
Old Oct 13, 2001 | 01:59 AM
  #3  
crucial's Avatar
Banned
 
Joined: Aug 2001
Posts: 246
Likes: 1
Definetly! The article in the tech section has a pic of a setup w/out a powersteering pump I believe ! Now how is that gonna help anybody with the new routing of the belt ? lol

------------------
1991 Z28 6.0 TPI

360 4 bolt main block, TrickFlow 23 degree heads, CompCams CS270HR cam, Harland Sharp roller rockers, Accel base, SLP siamesed runners, 52MM SLP Throttle Body, Hooker Headers, Flowmaster catback, MSD6A ignition, Home made ramair system, 2500 stall, bullet proof 700R4, aluminum driveshaft...
Reply
Old Oct 13, 2001 | 05:22 AM
  #4  
Omar's Avatar
Senior Member
 
Joined: Jul 1999
Posts: 994
Likes: 0
From: San Diego, CA
Yes, your coolant bypass will remain unaffected.

------------------
1989 IROC-Z 5.7L
NOS 5151 150HP kit
ProBuilt 700R4, PI Vigilante 2800 stall lockup
Baer Brakes 12" Sport System
Reply
Old Oct 13, 2001 | 10:02 AM
  #5  
Guest
Guest
 
Posts: n/a
Look closer, there are 2 different pics.
Reply
Old Oct 13, 2001 | 11:38 AM
  #6  
un4givin89's Avatar
Thread Starter
Banned
 
Joined: Jun 2001
Posts: 2,228
Likes: 1
From: Lan Terminal
I'm thinking a few different pictures, some more detialed info get some other peoples experinice...
Reply
Old Oct 13, 2001 | 04:13 PM
  #7  
un4givin89's Avatar
Thread Starter
Banned
 
Joined: Jun 2001
Posts: 2,228
Likes: 1
From: Lan Terminal
I can't get those little tubes off of the exhaust,fing A man, the little bastards are on good!
Reply
Old Oct 13, 2001 | 11:33 PM
  #8  
IROC&ROLL
Guest
 
Posts: n/a
A word to the wise: You better word your article properly (as in hypotheticals or "for offroad use only"). It's a major fine (as in federal crime) for tampering or assisting someone tamper with vehicle emmision controls.
Reply
Old Oct 13, 2001 | 11:42 PM
  #9  
un4givin89's Avatar
Thread Starter
Banned
 
Joined: Jun 2001
Posts: 2,228
Likes: 1
From: Lan Terminal
your full of crap, the otehr article says REMOVING YOUR SMOG PUMP. Nothign illegal about it, I went to get my car inspected and aked, and he said it was fine. It all depends were you live. Check with local and state laws.
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
italiano67
Tech / General Engine
8
Dec 11, 2016 09:21 AM
gta90
TPI
40
Sep 15, 2015 04:00 PM
86White_T/A305
LTX and LSX
0
Aug 17, 2015 12:16 AM
3rdgenparts
Interior Parts for Sale
0
Aug 8, 2015 07:09 PM
mustangman65_79
Exhaust
0
Aug 7, 2015 09:55 PM




All times are GMT -5. The time now is 08:58 AM.