400ci TPI?
Thread Starter
Junior Member
Joined: Dec 2002
Posts: 67
Likes: 0
From: Decatur, IL
400ci TPI?
just got this car had 31k miles perfect body but just got hit last night.
my granny backed into it :
color is Gold
The car has a custom built 400ci motor. The motor was built by MPG Race engines in Highland Park IL (847)432-2887. Here are the specs on the motor: CHEVY BOWTIE SMALL BLOCK, 4-BOLT SPLAYED MAINS 4.125 BORE 9.005 DECK ** BOTTOM END STUD KIT ** COLA FORGED CRANKSHAFT ** MANLEY STEEL CONNECTING RODS (4340 ALLOY) 5.85 ** ARIAS FORGED PISTONS (9.8:1 COMPRESSION) ** C & A ZGS PISTON RINGS ** C & A ENGINE BEARINGS ** HAMBURGER 7 QUART OIL PAN ** OIL PUMP (MANLEY) ** THRUST ASSEMBLY FOR HYDRAULIC ROLLER CAM ** COMP CAMS HYDRAULIC ROLLER 3119 / 3111 -HR14 ** 114 DEGREE LOBE SEPARATION, 110 DEGREE INTAKE CENTERLINE i.e. 4 DEGREE ADV. ** COMP CAMS 1.5:1 STAINLESS STEEL ROLLER ROCKERS ** BRODIX FSH-8 INTAKE RUNNER VOLUME 198cc APROX. (225 cfm INT, 165 cfm EXH.) ** MANLEY STAINLESS STEEL VALVES 2.055 AND 1.60 SEVERE DUTY ** TILTON STARTER ** HARMONIC BALANCER (SFI APPROVED) FLUID DAMPENER ** ENGINE MOUNTS (LIQUID TYPE LIKE LEXUS WITH WINE GLASSES AT 100 MPH) ** HEADERS (HOOKER CERAMIC COATED) 1 3/4in. SUPER COMP ** RADIATOR 5 CORE ** TWO 14in. ELECTRIC COOLING FANS ** 4L80E OVERDRIVE TRANSMISSION WITH HIGH STALL CONVERTER ** BLACK PAINT ENGINE ** 1989 CORVETTE TPI SYSTEM (SPEED DENSITY TYPE) EXTERNAL COIL HEI DISTRIBUTOR, O2 AND KNOCK SENSORS, PORTED PLENUM AND INTAKE MANIFOLD. ** 52MM THROTTLE BODY ** 24 LB/HR FUEL INJECTORS ** ACCEL POWER PROCESSOR W/ CALMAP ** WIRE HARNESS - HOWELL INDUSTRIES MODIFIED 1991 GM TRUCK HARNESS TBI TO TPI ** ACCEL FUEL PUMP 74702 720HP ** K & N AIR FILTER ** MSD 6AL IGNITION SYSTEM ** FORD 9”**RICHMOND 4:10 GEAR ** DISK BREAKS ALL 4 TIRES ** GAS TANK HAD A CUSTOM SUMP INSTALLED AND TEFLON COATED
The injectors are svo 24#'s, heads are brodix aluminum, the intake is off a 89 vette it has larger runners and has been ported and polished, and the cam is 224 int & 230 exh @ .050, and .550 lift intake & .575 lift exhaust
Wondering what this thing would make on the dyno
or at the track
any ideas?
it weighs about 4200 lbs with me in the car
my granny backed into it :
color is Gold
The car has a custom built 400ci motor. The motor was built by MPG Race engines in Highland Park IL (847)432-2887. Here are the specs on the motor: CHEVY BOWTIE SMALL BLOCK, 4-BOLT SPLAYED MAINS 4.125 BORE 9.005 DECK ** BOTTOM END STUD KIT ** COLA FORGED CRANKSHAFT ** MANLEY STEEL CONNECTING RODS (4340 ALLOY) 5.85 ** ARIAS FORGED PISTONS (9.8:1 COMPRESSION) ** C & A ZGS PISTON RINGS ** C & A ENGINE BEARINGS ** HAMBURGER 7 QUART OIL PAN ** OIL PUMP (MANLEY) ** THRUST ASSEMBLY FOR HYDRAULIC ROLLER CAM ** COMP CAMS HYDRAULIC ROLLER 3119 / 3111 -HR14 ** 114 DEGREE LOBE SEPARATION, 110 DEGREE INTAKE CENTERLINE i.e. 4 DEGREE ADV. ** COMP CAMS 1.5:1 STAINLESS STEEL ROLLER ROCKERS ** BRODIX FSH-8 INTAKE RUNNER VOLUME 198cc APROX. (225 cfm INT, 165 cfm EXH.) ** MANLEY STAINLESS STEEL VALVES 2.055 AND 1.60 SEVERE DUTY ** TILTON STARTER ** HARMONIC BALANCER (SFI APPROVED) FLUID DAMPENER ** ENGINE MOUNTS (LIQUID TYPE LIKE LEXUS WITH WINE GLASSES AT 100 MPH) ** HEADERS (HOOKER CERAMIC COATED) 1 3/4in. SUPER COMP ** RADIATOR 5 CORE ** TWO 14in. ELECTRIC COOLING FANS ** 4L80E OVERDRIVE TRANSMISSION WITH HIGH STALL CONVERTER ** BLACK PAINT ENGINE ** 1989 CORVETTE TPI SYSTEM (SPEED DENSITY TYPE) EXTERNAL COIL HEI DISTRIBUTOR, O2 AND KNOCK SENSORS, PORTED PLENUM AND INTAKE MANIFOLD. ** 52MM THROTTLE BODY ** 24 LB/HR FUEL INJECTORS ** ACCEL POWER PROCESSOR W/ CALMAP ** WIRE HARNESS - HOWELL INDUSTRIES MODIFIED 1991 GM TRUCK HARNESS TBI TO TPI ** ACCEL FUEL PUMP 74702 720HP ** K & N AIR FILTER ** MSD 6AL IGNITION SYSTEM ** FORD 9”**RICHMOND 4:10 GEAR ** DISK BREAKS ALL 4 TIRES ** GAS TANK HAD A CUSTOM SUMP INSTALLED AND TEFLON COATED
The injectors are svo 24#'s, heads are brodix aluminum, the intake is off a 89 vette it has larger runners and has been ported and polished, and the cam is 224 int & 230 exh @ .050, and .550 lift intake & .575 lift exhaust
Wondering what this thing would make on the dyno
or at the track
any ideas?
it weighs about 4200 lbs with me in the car
Supreme Member
Joined: Jul 1999
Posts: 5,183
Likes: 42
From: Oakdale, Ca
Car: 89 IrocZ
Engine: L98-ish
Transmission: 700R4
Wow, I thought everyone would be all over this...
Stock TPI will limit you engines potentional. Search this forum, and you'll save me a lot of typing.
My guess is you'll run strong, but you're losing mega-power-potential with a stock intake.
Sell the TPI, then look for mini-ram, Holley Sleathram, Accel Superram, etc, intakes.
Stock TPI will limit you engines potentional. Search this forum, and you'll save me a lot of typing.
My guess is you'll run strong, but you're losing mega-power-potential with a stock intake.
Sell the TPI, then look for mini-ram, Holley Sleathram, Accel Superram, etc, intakes.
Thread
Thread Starter
Forum
Replies
Last Post
Sanjay
Engine/Drivetrain/Suspension Parts for Sale
1
Aug 12, 2015 03:41 PM
