Third Generation F-Body Message Boards
Plastic and urethane welder. .
Plastic and urethane welder. .
0 2023/10/12 20:59:34
Bare cover just kinda sitting in place. .
Bare cover just kinda sitting in place. .
0 2023/10/12 20:59:36
This had been in a 88 Camaro but just got it for a few bolt on pieces I needed for my TPI engine build.
This had been in a 88 Camaro but just got it for a few bolt on pieces I needed for my TPI engine build.
0 2023/10/14 23:58:53
5.7 short block from an Iroc, will only be using the block for the 302 build. Also a set of TRW forged 11 to 1 pistons for it, flywheel and balancer.
5.7 short block from an Iroc, will only be using the block for the 302 build. Also a set of TRW forged 11 to 1 pistons for it, flywheel and balancer.
0 2023/10/14 23:59:36
The rear up, on jack stands and wheels off.
The rear up, on jack stands and wheels off.
0 2023/10/18 01:13:34
Front up on cribbings.
Front up on cribbings.
0 2023/10/18 01:13:36
0 2023/10/18 23:35:23
Both sets of fuel lines on my bench outside the shop.
Both sets of fuel lines on my bench outside the shop.
0 2023/10/18 23:35:54
Working on getting the blockages out.
Working on getting the blockages out.
0 2023/10/18 23:35:56
A little cleanup on the lines.
A little cleanup on the lines.
0 2023/10/18 23:35:58
Blanket down so I dont scratch the new paint. Will hang the rear first loosely and then bolt the front clamps in place.
Blanket down so I dont scratch the new paint. Will hang the rear first loosely and then bolt the front clamps in place.
0 2023/10/18 23:36:00
Bumper cover upside down on the bench to start repairs.
Bumper cover upside down on the bench to start repairs.
0 2023/10/18 23:36:23
Actually 2 Third Gens in this pic. The one under the cover is an 89 GTA.
Actually 2 Third Gens in this pic. The one under the cover is an 89 GTA.
0 2023/10/20 01:01:06
As mentioned at the start of this thread I'm not really restoring the car but rather rebuilding it as I plan on driving it and even doing some track days. Because of that I'm mostly leaving the bottom side untouched.
As mentioned at the start of this thread I'm not really restoring the car but rather rebuilding it as I plan on driving it and even doing some track days. Because of that I'm mostly leaving the bottom side untouched.
0 2023/10/21 00:37:05
The original lines fit so much better than the reproductions did.
The original lines fit so much better than the reproductions did.
0 2023/10/21 00:37:08
Top line will come down once the filter is installed.
Top line will come down once the filter is installed.
0 2023/10/21 00:37:09
Got the filter today so will get it in place along with its bracket over the weekend.
Got the filter today so will get it in place along with its bracket over the weekend.
0 2023/10/21 00:37:11
This shows how close the edge of the ground effect is to the jacking rail that was added. That is why originally the fiberglass got broken up and then later they cut a rectangular area out. I'll cut these too.
This shows how close the edge of the ground effect is to the jacking rail that was added. That is why originally the fiberglass got broken up and then later they cut a rectangular area out. I'll cut these too.
0 2023/10/21 00:37:13
I've got to cut the wire ties but left them in place until all the lines are bolted in place.
I've got to cut the wire ties but left them in place until all the lines are bolted in place.
0 2023/10/21 00:37:14
I lost a clamp somewhere but will pull one off the parts car.
I lost a clamp somewhere but will pull one off the parts car.
0 2023/10/21 00:37:16
Taking parts off one of my spare 9 bolts. This one had the PBR's on it from the factory.
Taking parts off one of my spare 9 bolts. This one had the PBR's on it from the factory.
0 2023/10/21 20:40:01
Couldnt get the ratchet and socket in to pull the pin so got creative.
Couldnt get the ratchet and socket in to pull the pin so got creative.
0 2023/10/21 20:40:03
4th Gen caliper on the top that I was sent as a 3rd Gen. Yeah they will swap but not correct for this car.
4th Gen caliper on the top that I was sent as a 3rd Gen. Yeah they will swap but not correct for this car.
0 2023/10/21 20:40:06
Getting the pin loose on the other caliper.
Getting the pin loose on the other caliper.
0 2023/10/21 20:40:07
Pulling the other pin.
Pulling the other pin.
0 2023/10/21 20:40:09
R and L calipers off the spare rear.
R and L calipers off the spare rear.
0 2023/10/21 20:40:11
Test spray on a small spot on the booster.
Test spray on a small spot on the booster.
0 2023/10/21 20:40:12
Calipers off the car on the left and the ones on the right off the spare rear.
Calipers off the car on the left and the ones on the right off the spare rear.
0 2023/10/21 20:40:14
More random rear disc parts I had, these are 4th Gen calipers.
More random rear disc parts I had, these are 4th Gen calipers.
0 2023/10/21 20:40:16
Driver side apart.
Driver side apart.
0 2023/10/21 20:40:17
Passenger side apart.
Passenger side apart.
0 2023/10/21 20:40:19
New lines on top and old ones bottom.
New lines on top and old ones bottom.
0 2023/10/21 20:50:44
Wrong new hose top.
Wrong new hose top.
0 2023/10/21 20:50:46
Centers look pretty close.
Centers look pretty close.
0 2023/10/21 20:50:47
Def not even close on this side.
Def not even close on this side.
0 2023/10/21 20:50:49
0 2023/10/21 20:55:19
New filter and its bracket back in place. .
New filter and its bracket back in place. .
0 2023/10/23 00:20:32
Getting the new front to rear brake line in place. .
Getting the new front to rear brake line in place. .
0 2023/10/23 00:20:34
Torque arm loosely in place. .
Torque arm loosely in place. .
0 2023/10/23 00:20:36
Wiring harness bolted back to the firewall. .
Wiring harness bolted back to the firewall. .
0 2023/10/23 00:20:37