Third Generation F-Body Message Boards
Left the harness o the cowl for now until I get the heater box back on. .
Left the harness o the cowl for now until I get the heater box back on. .
0 2023/10/23 00:20:40
Taking it apart for the bracket and clip. .
Taking it apart for the bracket and clip. .
0 2023/10/23 00:20:41
Using a line wrench. .
Using a line wrench. .
0 2023/10/23 00:20:43
Line wrenches keep you from stripping out the tube nuts. .
Line wrenches keep you from stripping out the tube nuts. .
0 2023/10/23 00:20:44
New hose installed on the one side. .
New hose installed on the one side. .
0 2023/10/23 00:20:46
Spraying the reservoir bracket.
Spraying the reservoir bracket.
0 2023/10/23 00:20:48
My fb marketplace score for the week.
My fb marketplace score for the week.
0 2023/10/23 23:11:05
This end has damage from the same wreck that messed up the quarter so will be repairing it.
This end has damage from the same wreck that messed up the quarter so will be repairing it.
0 2023/10/23 23:11:07
Lots of layers of paint.
Lots of layers of paint.
0 2023/10/23 23:11:08
As many times as it had been repainted was surprised to see it still had an emblem.
As many times as it had been repainted was surprised to see it still had an emblem.
0 2023/10/23 23:11:11
0 2023/10/24 20:57:17
Spraying the PBR calipers with an acid cleaner to get some of the grime off them.
Spraying the PBR calipers with an acid cleaner to get some of the grime off them.
0 2023/10/24 20:57:19
Got most of it off, will be fine back on the car plus they will just get dirty again.
Got most of it off, will be fine back on the car plus they will just get dirty again.
0 2023/10/24 20:57:21
Getting ready to install the new pads.
Getting ready to install the new pads.
0 2023/10/24 20:57:22
Mocking the rotor to caliper back up on the bench.
Mocking the rotor to caliper back up on the bench.
0 2023/10/24 20:57:24
Driver side back on the car.
Driver side back on the car.
0 2023/10/24 20:57:26
Passenger side bolted back on.
Passenger side bolted back on.
0 2023/10/24 20:57:28
0 2023/10/25 18:06:52
Had to go to 80 grit to get through most of the paint layer and then will finish it with 180.
Had to go to 80 grit to get through most of the paint layer and then will finish it with 180.
0 2023/10/26 01:18:14
Not a lot of space between it and the wall but will make due.
Not a lot of space between it and the wall but will make due.
0 2023/10/26 01:18:15
All that dust on the floor is from today.
All that dust on the floor is from today.
0 2023/10/26 01:18:17
Have to repair a spot where the bumper cover is split above the exhaust.
Have to repair a spot where the bumper cover is split above the exhaust.
0 2023/10/26 23:57:18
Finished stripping the bumper cover.
Finished stripping the bumper cover.
0 2023/10/26 23:57:20
More sanding on the quarter to knock down some high spots. I had just roughed it in prior.
More sanding on the quarter to knock down some high spots. I had just roughed it in prior.
0 2023/10/26 23:57:22
Another sanding pass on most of the driver side.
Another sanding pass on most of the driver side.
0 2023/10/26 23:57:23
Same for the passenger.
Same for the passenger.
0 2023/10/26 23:57:25
Starting tear.
Starting tear.
0 2023/10/28 19:11:29
This was after beveling it with a dremel but I found I had to open it up even more for the urethane to hold.
This was after beveling it with a dremel but I found I had to open it up even more for the urethane to hold.
0 2023/10/28 19:11:31
Second pass with the welder after opening the groove back more.
Second pass with the welder after opening the groove back more.
0 2023/10/28 19:11:33
You feed the urethane rod through the hole in the foot.
You feed the urethane rod through the hole in the foot.
0 2023/10/28 19:11:36
After rough grinding.
After rough grinding.
0 2023/10/28 19:11:37
After sanding with 80 grit.
After sanding with 80 grit.
0 2023/10/28 19:11:39
This is the damage on the back. I'm not going to replace the missing chunk but rather fix just the tears.
This is the damage on the back. I'm not going to replace the missing chunk but rather fix just the tears.
0 2023/10/28 19:11:40
After the first pass with urethane.
After the first pass with urethane.
0 2023/10/28 19:11:42
I'm not sure on this exhaust as it is date coded 1988 and Dynomax was a sponsor but I think it was added later or that Matt may have added it as it favors the SLP and GMMG stuff.
I'm not sure on this exhaust as it is date coded 1988 and Dynomax was a sponsor but I think it was added later or that Matt may have added it as it favors the SLP and GMMG stuff.
0 2023/10/28 19:11:43
After grinding.
After grinding.
0 2023/10/28 19:11:45
Taping the rear up ahead of spraying epoxy.
Taping the rear up ahead of spraying epoxy.
0 2023/10/28 19:11:47
Clutch master cylinder came in and I already had the bracket for the reservoir and the new reservoir.
Clutch master cylinder came in and I already had the bracket for the reservoir and the new reservoir.
0 2023/10/28 19:22:59
3 sets of brake line, the factory lines off the spare 89 rear that had PBR's, the set I got last year that turned out to be wrong and the set that just came in.
3 sets of brake line, the factory lines off the spare 89 rear that had PBR's, the set I got last year that turned out to be wrong and the set that just came in.
0 2023/10/28 19:23:00
Close but still not the same, I add the bends as needed.
Close but still not the same, I add the bends as needed.
0 2023/10/28 19:23:02