Third Generation F-Body Message Boards
0 2018/12/01 12:41:23
0 2019/03/03 16:15:13
0 2019/03/03 16:16:25
0 2019/03/03 16:16:33
Newer Autozone egr with brand new temp sensor. The egr was replaced in 2014 and has less than 15k miles on it. The brand new temp sensor was replaced in 2016 and was about $45 by itself.. $60 shipped for the pair. $30+ shipping individually.
Newer Autozone egr with brand new temp sensor. The egr was replaced in 2014 and has less than 15k miles on it. The brand new temp sensor was replaced in 2016 and was about $45 by itself.. $60 shipped for the pair. $30+ shipping individually.
0 2019/03/31 14:19:56
These abc perimeter bolt valve covers are new and in good condition, some smudgy finger prints and stains on them that I’ll clean off before shipping. Can’t remember what brand they are but I got them off summit and they came in a red box. Make me an offer on them
These abc perimeter bolt valve covers are new and in good condition, some smudgy finger prints and stains on them that I’ll clean off before shipping. Can’t remember what brand they are but I got them off summit and they came in a red box. Make me an offer on them
0 2019/03/31 14:20:03
TPI Intake manifold off of my 86 trans am. Not sure what these go for, make an offer
TPI Intake manifold off of my 86 trans am. Not sure what these go for, make an offer
0 2019/03/31 14:20:14
Throttle body off of my 86 trans am. I’m sure the throttle shaft bushings are most likely worn. The tps and iac sensors are autozone replacements I put on the car back in 2014. Maybe 15k-20k on them. $60shipped for the whole thing. Make an offer if you just want the tps, iac, or throttle body by itself
Throttle body off of my 86 trans am. I’m sure the throttle shaft bushings are most likely worn. The tps and iac sensors are autozone replacements I put on the car back in 2014. Maybe 15k-20k on them. $60shipped for the whole thing. Make an offer if you just want the tps, iac, or throttle body by itself
0 2019/03/31 14:20:22
Replacement hei distributor cap with original coil cap and autozone replacement coil. The distributor cap has black over spray on it and some oxidization on the contact points inside the cap. The coil alone was around $25. I’ll do the whole thing for $40 shipped
Replacement hei distributor cap with original coil cap and autozone replacement coil. The distributor cap has black over spray on it and some oxidization on the contact points inside the cap. The coil alone was around $25. I’ll do the whole thing for $40 shipped
0 2019/03/31 14:20:34
0 2019/03/31 14:20:42
Cat to tail shaft mount with some(maybe all?) of the hardware. Make an offer
Cat to tail shaft mount with some(maybe all?) of the hardware. Make an offer
0 2019/03/31 14:20:51
0 2019/04/03 17:54:54
0 2019/06/27 19:05:39
0 2019/06/27 19:05:49
0 2019/06/27 19:05:56
0 2019/06/27 19:06:06
0 2019/06/27 19:09:46
0 2019/10/12 16:37:22
0 2019/10/12 16:38:14
0 2019/10/12 18:15:10
0 2019/10/19 17:20:35
0 2019/10/19 17:20:44
0 2019/10/19 17:20:53
0 2019/10/20 08:13:24
0 2019/10/20 08:13:34
0 2019/10/23 19:54:11
0 2019/10/23 19:54:19
0 2020/01/24 12:12:58
This was the worst section of the front channel, as you can tell in the pic it rotted the inside face of the t top section as well
This was the worst section of the front channel, as you can tell in the pic it rotted the inside face of the t top section as well
0 2022/10/21 18:25:57
Here's the front channel partially ripped up, showing the damage under neath
Here's the front channel partially ripped up, showing the damage under neath
0 2022/10/21 18:25:59
the passenger side
the passenger side
0 2022/10/21 18:26:02
Here's the back channel also partially ripped up
Here's the back channel also partially ripped up
0 2022/10/21 18:26:04
This is the front without the channel, the metal underneath also needed to be replaced
This is the front without the channel, the metal underneath also needed to be replaced
0 2022/10/21 18:29:42
Same goes for the back
Same goes for the back
0 2022/10/21 18:29:46
I removed the bad sheet metal from the picture prior to this, cleaned up the metal under neath, and cut out the rotted metal on the front roof section itself
I removed the bad sheet metal from the picture prior to this, cleaned up the metal under neath, and cut out the rotted metal on the front roof section itself
0 2022/10/21 18:31:09
Here's the replacement patch I made for that section, I unfortunately don't have pictures but I used a shrinker and stretcher set I got from harbor freight to match the curve, rounded the edge over to match the curve of the roof
Here's the replacement patch I made for that section, I unfortunately don't have pictures but I used a shrinker and stretcher set I got from harbor freight to match the curve, rounded the edge over to match the curve of the roof
0 2022/10/21 18:31:11
Here's that panel welded in, I did some hammer and smoothing work after this but don't have any pictures
Here's that panel welded in, I did some hammer and smoothing work after this but don't have any pictures
0 2022/10/21 18:31:13
This is how I shaped the sheet metal going under the front t top channel, did the same for the back channel as well
This is how I shaped the sheet metal going under the front t top channel, did the same for the back channel as well
0 2022/10/21 18:34:41
You can see the shrinking marks on the panel, a couple more tweaks after this and it fit well
You can see the shrinking marks on the panel, a couple more tweaks after this and it fit well
0 2022/10/21 18:34:44
different view of the other side
different view of the other side
0 2022/10/21 18:34:46