Third Generation F-Body Message Boards
0 2022/01/12 16:00:33
0 2022/01/12 16:00:41
0 2022/01/12 16:00:48
0 2022/01/12 16:01:00
0 2022/01/12 16:01:07
0 2022/02/07 18:06:36
0 2022/02/07 18:06:53
0 2022/02/07 18:13:04
0 2022/02/07 18:13:20
Passenger side manifold to y-pipe. I will probably end up re-routing power wires since it is a little close for comfort. you can see an almost 90 turn down is required on this side.
Passenger side manifold to y-pipe. I will probably end up re-routing power wires since it is a little close for comfort. you can see an almost 90 turn down is required on this side.
0 2022/04/02 14:45:23
Driver side manifold to y-pipe. This one went more straight down but the merge in the manifold still makes the clamp pretty close to the firewall. I am going to watch this one to see if it ends up hitting.
Driver side manifold to y-pipe. This one went more straight down but the merge in the manifold still makes the clamp pretty close to the firewall. I am going to watch this one to see if it ends up hitting.
0 2022/04/02 14:47:03
Driver's side underneath. This is where I located the O2 sensor since flipping into the back side there would not have been any room. This has more than enough room to get a wrench on it and tighten it.
Driver's side underneath. This is where I located the O2 sensor since flipping into the back side there would not have been any room. This has more than enough room to get a wrench on it and tighten it.
0 2022/04/02 14:51:41
Where passenger side down pipe meets crossover pipe. More than enough clearance around everything.
Where passenger side down pipe meets crossover pipe. More than enough clearance around everything.
0 2022/04/02 14:53:46
Backside of passenger downpipe where Passenger side O2 sensor will be located
Backside of passenger downpipe where Passenger side O2 sensor will be located
0 2022/04/02 14:57:34
Outlet of Y-pipe falls perfectly in stock location. Still have to make sure that tires fit but I don't see a problem here.
Outlet of Y-pipe falls perfectly in stock location. Still have to make sure that tires fit but I don't see a problem here.
0 2022/04/02 14:59:02
Here you can see how low it hangs. It isn't perfect since it still hangs about 1.5" below k-member but I am happy with it.
Here you can see how low it hangs. It isn't perfect since it still hangs about 1.5" below k-member but I am happy with it.
0 2022/04/02 15:00:09
Overall shape and routing. You can see the down pipes for either side are because of how different the truck manifolds exit. I also flattened the center section to help with clearance.
Overall shape and routing. You can see the down pipes for either side are because of how different the truck manifolds exit. I also flattened the center section to help with clearance.
0 2022/04/02 15:01:37
Driver side manifold
Driver side manifold
0 2022/04/02 15:18:10
Passenger side manifold
Passenger side manifold
0 2022/04/02 15:19:30
0 2022/04/20 17:43:16
Accessory set up with Holley kit. Power steering pump was a GM saginaw type II. Using a camaro ls1 waterpump.
Accessory set up with Holley kit. Power steering pump was a GM saginaw type II. Using a camaro ls1 waterpump.
0 2022/04/20 18:06:36
Lower radiator hose was a modified 2.8 v6 3rd gen camaro hose that was shortened.
Lower radiator hose was a modified 2.8 v6 3rd gen camaro hose that was shortened.
0 2022/04/20 18:08:22
Stock 4th gen ls1 camaro upper radiator hose fits perfectly.
Stock 4th gen ls1 camaro upper radiator hose fits perfectly.
0 2022/04/20 18:10:11
Power steering line. You can see the hard line that has -8an fitting coming from the top of the power steering pump. This is holley part No. 198-202.
Power steering line. You can see the hard line that has -8an fitting coming from the top of the power steering pump. This is holley part No. 198-202.
0 2022/04/20 18:11:43
Powersteering line I had made at my local hydraulic line for $40. I specified -8 JIC fittings which will work with the -8an fittings on the steering box and the power steering pump
Powersteering line I had made at my local hydraulic line for $40. I specified -8 JIC fittings which will work with the -8an fittings on the steering box and the power steering pump
0 2022/04/20 18:16:28
Overall shot of the engine bay in the state to get it running. I plan on getting rid of the big inlet pipe and use the stock air box. Before I pull the engine out I am going to wrap wiring and loom it all to clean it up.
Overall shot of the engine bay in the state to get it running. I plan on getting rid of the big inlet pipe and use the stock air box. Before I pull the engine out I am going to wrap wiring and loom it all to clean it up.
0 2022/04/20 18:18:57
0 2022/04/22 17:39:52
0 2022/04/22 17:40:39
0 2022/04/22 17:41:05
0 2024/07/04 08:25:43
0 2024/07/04 08:25:45
0 2024/07/04 08:25:47
0 2024/07/04 08:25:49
0 2024/07/04 08:25:51
0 2024/12/08 17:54:23
0 2024/12/08 17:54:27
0 2024/12/08 17:54:30
0 2024/12/08 17:54:33
0 2024/12/08 17:54:36
0 2024/12/08 17:54:47