Third Generation F-Body Message Boards
(aftermarket) rubber bump stop trimmed about 3/8in
(aftermarket) rubber bump stop trimmed about 3/8in
0 2020/12/26 00:43:38
painted over bare metal
painted over bare metal
0 2020/12/26 00:43:49
you will need to hammer this area to clear the tire. SUPER easy and fast
you will need to hammer this area to clear the tire. SUPER easy and fast
0 2020/12/26 00:46:38
rear bump stops were trimmed in height so i could lower the car more. no tires rub when rub on the bump stops
rear bump stops were trimmed in height so i could lower the car more. no tires rub when rub on the bump stops
0 2020/12/26 00:49:34
0 2020/12/26 00:52:45
I used little 12mm x 1.5 acorn nuts as the WELD wheels have small Tapered seats.
I used little 12mm x 1.5 acorn nuts as the WELD wheels have small Tapered seats.
0 2020/12/26 00:53:08
The acorn nuts have a dumb socket
The acorn nuts have a dumb socket
0 2020/12/26 00:53:20
A quick pass with a TIG welder makes a single socket. Spline socket+21MM SOCKET
A quick pass with a TIG welder makes a single socket. Spline socket+21MM SOCKET
0 2020/12/26 00:54:02
3.in Extended ARP studs have plenty of grip range left even with a 5/8 spacer
3.in Extended ARP studs have plenty of grip range left even with a 5/8 spacer
0 2020/12/26 00:54:45
my 13in 6 piston Wilwood brakes with Billet aluminum hubs fit easily.
my 13in 6 piston Wilwood brakes with Billet aluminum hubs fit easily.
0 2020/12/26 00:56:11
the WELDS71 wheels have a smaller center section and larhe shells, so they look closer to 16s than they do 18s. this help with aesthetics
the WELDS71 wheels have a smaller center section and larhe shells, so they look closer to 16s than they do 18s. this help with aesthetics
0 2020/12/26 00:58:15
clears my tubular LCA no issues
clears my tubular LCA no issues
0 2020/12/26 00:59:43
my 92 Autocross car with a unfinished 10in spoiler
my 92 Autocross car with a unfinished 10in spoiler
0 2020/12/26 01:04:55
18x11 on the rear
18x11 on the rear
0 2020/12/26 01:05:28
my Camber bolts reduce clearance a bit, but the strut and wheel do not touch.
my Camber bolts reduce clearance a bit, but the strut and wheel do not touch.
0 2020/12/26 01:05:57
side pic of the 18X11 forged 3 piece welded wheel
side pic of the 18X11 forged 3 piece welded wheel
0 2020/12/26 01:06:25
hub cap O.D.
hub cap O.D.
0 2020/12/26 01:07:57
Hub cap Height
Hub cap Height
0 2020/12/26 01:08:32
295/30R18 A)52 tires monted
295/30R18 A)52 tires monted
0 2020/12/26 01:09:01
perfect fit on these 18x11s Autocross tires are awesome, but don't store them under 40F weather
perfect fit on these 18x11s Autocross tires are awesome, but don't store them under 40F weather
0 2020/12/26 01:09:16
tape on the bumper for chin splitter fitment
tape on the bumper for chin splitter fitment
0 2020/12/26 01:10:05
on the bump stops
on the bump stops
0 2020/12/26 01:10:45
rear tires are about 1/8in inside the rear fenders
rear tires are about 1/8in inside the rear fenders
0 2020/12/26 01:12:33
0.600in Thick spacer 5x4.75 bolt pattern 2.78in bore I.D.
0.600in Thick spacer 5x4.75 bolt pattern 2.78in bore I.D.
0 2020/12/26 01:44:33
5/8in spacer 3d printed center to reduce the I.D to 3rd gen spec Of 2.77in
5/8in spacer 3d printed center to reduce the I.D to 3rd gen spec Of 2.77in
0 2020/12/29 00:34:57
Earl's SS lines -3am With ground control KONI RACE double Adjustable 8611-1259 Struts. Line bolts in the same spot as sock.
Earl's SS lines -3am With ground control KONI RACE double Adjustable 8611-1259 Struts. Line bolts in the same spot as sock.
0 2020/12/31 09:31:51
QA1 Ultimate Ball-Joint with 0.5in extended stud. 0.200 and stock lenght are available and can be swapped in no issue.
QA1 Ultimate Ball-Joint with 0.5in extended stud. 0.200 and stock lenght are available and can be swapped in no issue.
0 2020/12/31 09:32:25
0 2021/01/02 10:57:03
0 2021/01/03 15:38:46
0 2021/01/03 15:38:59
2 stitch welds instead of the 4 it needs
2 stitch welds instead of the 4 it needs
0 2021/01/08 20:37:37
This is the undamaged passenger side, but this is where the split was happening.
This is the undamaged passenger side, but this is where the split was happening.
0 2021/01/08 20:37:48
Extra 2 stitch welds added for a total of 4
Extra 2 stitch welds added for a total of 4
0 2021/01/08 20:38:33
Blasted after welding
Blasted after welding
0 2021/01/08 20:38:50
POR-15 Chassis paint and they are good as new
POR-15 Chassis paint and they are good as new
0 2021/01/08 20:39:00
before blasting a quick TIG fillet weld with mild steel filler wire
before blasting a quick TIG fillet weld with mild steel filler wire
0 2021/01/08 20:49:09
Billet 6061 Aluminum Prototype
Billet 6061 Aluminum Prototype
0 2021/01/08 20:50:49
3d printed, still need changes including a mono ball
3d printed, still need changes including a mono ball
0 2021/01/08 20:53:01
0 2021/01/26 14:00:20
0 2021/01/26 14:00:25