Third Generation F-Body Message Boards
0 2019/01/10 21:10:37
0 2019/01/10 21:08:55
0 2019/01/10 21:08:41
0 2019/01/10 21:08:27
0 2019/01/10 21:08:16
0 2019/01/10 21:08:04
0 2019/01/10 21:07:52
0 2019/01/10 21:07:39
0 2019/01/10 21:07:27
0 2019/01/10 21:07:16
0 2019/01/10 21:06:42
0 2019/01/10 21:06:23
0 2019/01/10 21:06:04
0 2019/01/10 21:05:47
0 2019/01/10 21:05:20
0 2019/01/10 21:04:59
0 2019/01/10 21:04:39
0 2019/01/10 21:04:24
0 2019/01/10 21:03:25
0 2019/01/10 21:03:00
0 2019/01/10 21:02:38
0 2019/01/10 21:02:24
0 2019/01/10 21:02:09
0 2019/01/10 21:01:23
0 2019/01/10 21:01:05
Modifying the brake pedal assembly for a msnual wilwood master. It gets mounted higher and a new pivot pin has to be put into the pedal lever. Getting close but with putting in custom stuff its never just bolt on.
Modifying the brake pedal assembly for a msnual wilwood master. It gets mounted higher and a new pivot pin has to be put into the pedal lever. Getting close but with putting in custom stuff its never just bolt on.
0 2019/01/05 16:47:42
Got time to install my UMI Performance bump steer correction kit. Very nice parts! And very straight forward install. Also got word the UMI rear weight jacks are in and shipping. Cant wait to get those along with their rear sway bar. If you get a chance check their parts out. Once i get mine ill take photos.
Got time to install my UMI Performance bump steer correction kit. Very nice parts! And very straight forward install. Also got word the UMI rear weight jacks are in and shipping. Cant wait to get those along with their rear sway bar. If you get a chance check their parts out. Once i get mine ill take photos.
0 2019/01/03 21:42:04
Just wanted it to look cleaner
Just wanted it to look cleaner
0 2018/12/29 22:28:27
0 2018/12/29 22:28:09
So i made inner fender well panels out of plastic sheet.
So i made inner fender well panels out of plastic sheet.
0 2018/12/29 22:27:51
I just couldnt stand looking into the huge wheel wells and seeing the ugly firewall/cowl.
I just couldnt stand looking into the huge wheel wells and seeing the ugly firewall/cowl.
0 2018/12/29 22:27:31
0 2018/12/29 22:25:56
So i made inner fender well panels out of plastic sheet.
So i made inner fender well panels out of plastic sheet.
0 2018/12/29 22:24:31
I couldnt stand to look into the huge wheel wells and see the ugly firewall/cowl.
I couldnt stand to look into the huge wheel wells and see the ugly firewall/cowl.
0 2018/12/29 22:22:46
Got my new aluminum drive shaft. Thanks to Jeff Gilroy at Inland Empire driveline i know i wont have to worry about that. The white was my idea for the old school nascar styling.
Got my new aluminum drive shaft. Thanks to Jeff Gilroy at Inland Empire driveline i know i wont have to worry about that. The white was my idea for the old school nascar styling.
0 2018/11/30 23:12:07
0 2018/11/20 18:01:31
Got the 9" in the car. Measured for a new drive shaft. Inland Empire Driveline should have it done in about s week.
Got the 9" in the car. Measured for a new drive shaft. Inland Empire Driveline should have it done in about s week.
0 2018/11/20 18:01:11
Rear is finally finished. Will try to pick it up tomorrow.
Rear is finally finished. Will try to pick it up tomorrow.
0 2018/11/08 12:41:47
0 2018/10/30 11:35:52
Back from powder coat. Getting partially assembled. Waiting on axles to be made from Speedway Eng. But i know with SEMA this week ill have a little bit of a delay on getting them. Excited to get it in the car.
Back from powder coat. Getting partially assembled. Waiting on axles to be made from Speedway Eng. But i know with SEMA this week ill have a little bit of a delay on getting them. Excited to get it in the car.
0 2018/10/30 11:35:37