Third Generation F-Body Message Boards
0 2022/09/15 17:47:48
0 2022/09/15 17:47:46
0 2022/09/15 17:47:43
0 2022/09/14 19:09:40
Since it's been too hot to be out side here at 109 with 40%+ humidity Ive been staying indoors. So I started playing with my new gauge cluster.
Since it's been too hot to be out side here at 109 with 40%+ humidity Ive been staying indoors. So I started playing with my new gauge cluster.
0 2022/09/05 20:39:44
0 2022/08/22 08:03:02
All back together. Ran out of daylight, so one day after work I'll check the timing and adjust the valves. But should be close. The Time-Serts went in super easy. I was stressing over them as the corner holes I needed them were counter bored already. But it wasn't an issue.
All back together. Ran out of daylight, so one day after work I'll check the timing and adjust the valves. But should be close. The Time-Serts went in super easy. I was stressing over them as the corner holes I needed them were counter bored already. But it wasn't an issue.
0 2022/08/01 08:01:23
It's kinda hard to see when the hood is closed in photos. But if you see here the pan extends over the top of the cowl with raised sides. And I've cut the hood seal to allow air in.
It's kinda hard to see when the hood is closed in photos. But if you see here the pan extends over the top of the cowl with raised sides. And I've cut the hood seal to allow air in.
0 2022/07/26 07:17:34
Ok got my Time Sert kit. Don't feel like doing it tonight so probably tomorrow. Then start putting It back together again. This time it will Torque down properly and actually seal.
Ok got my Time Sert kit. Don't feel like doing it tonight so probably tomorrow. Then start putting It back together again. This time it will Torque down properly and actually seal.
0 2022/07/25 13:17:38
Got it all back apart again. Gotta Time Cert the end intake bolt holes. So I took out the lifters and gave them a good cleaning just cuz I was there. I've got it all cleaned and ready to go back together now. Just gotta pick up the Time Certs from Specialty Fasteners tomorrow.
Got it all back apart again. Gotta Time Cert the end intake bolt holes. So I took out the lifters and gave them a good cleaning just cuz I was there. I've got it all cleaned and ready to go back together now. Just gotta pick up the Time Certs from Specialty Fasteners tomorrow.
0 2022/07/23 20:42:38
And they have many masters. I was visioning maybe one of these could work for you? But again Ive not messed with the clutches on these to know what stock set up even looks like.
And they have many masters. I was visioning maybe one of these could work for you? But again Ive not messed with the clutches on these to know what stock set up even looks like.
0 2022/07/15 22:41:06
Yeah I think they only have the one slave
Yeah I think they only have the one slave
0 2022/07/15 22:41:03
Even with the stock manifolds I think it's looking pretty good.
Even with the stock manifolds I think it's looking pretty good.
0 2022/07/14 20:20:04
Some heat wrap replacing the stock crappy plastic loom.
Some heat wrap replacing the stock crappy plastic loom.
0 2022/07/14 20:19:57
0 2022/07/14 20:19:50
Spark plug wires loomed by zip tie. Valve Covers fit
Spark plug wires loomed by zip tie. Valve Covers fit
0 2022/07/14 20:19:42
Most of the way back together. Probably would have gotten more done if I wasn't out so late at the races last night at Orangeshow Speedway. But gotta get my fix.
Most of the way back together. Probably would have gotten more done if I wasn't out so late at the races last night at Orangeshow Speedway. But gotta get my fix.
0 2022/07/10 16:05:02
Got the intake all cleaned up and repainted. Throttle body is clean and ready to go. Gotta get up early tomorrow to start putting it back together.
Got the intake all cleaned up and repainted. Throttle body is clean and ready to go. Gotta get up early tomorrow to start putting it back together.
0 2022/07/09 14:15:16
Not too bad looking inside for as many miles as it has
Not too bad looking inside for as many miles as it has
0 2022/07/09 14:14:54
Glad Im doing this now. the intake gasket was not looking good. If I had waited much longer I think it could have gotten pretty bad.
Glad Im doing this now. the intake gasket was not looking good. If I had waited much longer I think it could have gotten pretty bad.
0 2022/07/09 14:14:53
Taking it apart now.
Taking it apart now.
0 2022/07/09 14:14:48
0 2022/07/06 13:52:22
0 2022/07/06 13:52:20
0 2022/07/06 13:52:18
0 2022/07/06 13:43:26
0 2022/07/06 13:43:24
0 2022/07/06 13:42:32
0 2022/07/06 13:42:31
0 2022/07/06 13:42:30
0 2022/07/06 13:42:29
0 2022/07/06 13:40:25
0 2022/07/06 13:40:24
0 2022/07/06 13:40:23
0 2022/07/06 13:40:21
I went a little out of order of what I want and need to get done. But I only had one day this weekend and I knew the airbox would be a days work. So there it is.
I went a little out of order of what I want and need to get done. But I only had one day this weekend and I knew the airbox would be a days work. So there it is.
0 2022/07/02 18:57:55
I kinda went out of order for what I want and need to get done. But I knew the airbox would be a days job. And that's all I had this weekend so I figured what the hell.
I kinda went out of order for what I want and need to get done. But I knew the airbox would be a days job. And that's all I had this weekend so I figured what the hell.
0 2022/07/02 18:53:58
First step in trying to make the stock engine look a little better. Relocating the heater control valve and the smog air diverter valve.
First step in trying to make the stock engine look a little better. Relocating the heater control valve and the smog air diverter valve.
0 2022/06/25 15:40:08
Now you can see and remove the passenger side valve cover.
Now you can see and remove the passenger side valve cover.
0 2022/06/25 15:39:14
0 2022/06/25 15:39:06
Haven't gotten around to the gauges or fixing the leaking intake manifold yet.
Haven't gotten around to the gauges or fixing the leaking intake manifold yet.
0 2022/06/14 21:27:22