Prices dont include shipping.

LT1 Intake modified for a Thirdgen, comes complete with fuellines/rails, lt1 24lb/hr injectors, and waterlines and remote thermostat housing. $280

BBK 58mm Throttle Body $250

Trickflow 23* Aluminum Heads. Ported and Polished by Lloyd Elliot. Intake flows 270.1 at .550 and exhaust flows 197.1 at .550. 58cc chambers and springs good to .600 lift. $1100

Comp Cams Pro Mag 1.6 roller rockers. Non self-alligning and 7/16 studs. $175

Comp Cams Extreme Energy Cam. #08-503-8. 224/230 112 LS .536/.544 with 1.6 rr's. $175

SLP 1 3/4 shorty headers that have been Jet-Hot coated. Includeds y-pipe. $550

Accel 60109 billetech distributor. $165

Built 355 shortblock with 20,000 miles. Block bored .030 over with deckplates, Keith Black Hypereutectic pistons, sealed power moly piston rings, 5140 forged steel rods, lt1 crankshaft, clevite rod main bearings and balanced by wayne calvert. $600

Serpentine setup. Complete with all brackets, and ac compressor, water pump, power steering pump and everything need to make the setup complete. $250

Professionally built 700r4 transmission with 5,000 miles. Built to handle 700 hp. Comes with a lockup 2800 stall torque converter. $1000

10-bolt rearend with 3.73 gears. Comes with a TA Performance 10-bolt Rear End Support (Diff Cover). $425

BMR Boxed Lower Control Arms $130

BMR Panhard Rod $70

BMR Non-Adjustable Torque Arm $175

 

Could you post some pics of the intake?

 

PM sent on heads

 

i will take intake! pm payment info please. thank you

 

I don't know how to post pictures on here but the car is still together. Need to move a car that's getting long tubes and then it will be apart. I can get everything out and apart in about a day and that will be this week. liltrevino pm me about the intake.

 

Prices are negotiable. Bill

 

I sent you a PM asking for pictures of the heads two weeks ago, and never got a response. So do you really want to sell these items, or what?

 

where in Texas are you located?

 

Did the intake sell? If not would you consider parting it? I need the lines, hoses and remote t-stat.

 

I have a sale pending on the intake. Bill

 

are they heads for lt1? If not what years?

 

The heads are for 87 and newer non LT1 engines. Bill

 

pm slp headers

 

PM sent

 

Do you have pictures of the rearend?
Would it fit on a 92 RS?
Any idea on freight costs to Denver Colorado?



10-bolt rearend with 3.73 gears. Comes with a TA Performance 10-bolt Rear End Support (Diff Cover). $425

 

Do you have pictures of the rearend?
Would it fit on a 92 RS?
Any idea on freight costs to Denver Colorado?



10-bolt rearend with 3.73 gears. Comes with a TA Performance 10-bolt Rear End Support (Diff Cover). $425

 

It will fit a 92 RS. It's still under the car but I'll take some picks of it under the car if you like. Bill

 

Im intrested in the cam.Have you got pics of it?

 

Cam is currently still in the car but should be out in the next day or so! Heads and headers and intake are off and I have pics of them. Let me know guys.

Bill

 

please send pics of the cam to eds01ss@yahoo.com asap

 

Interested in the heads and motor, as stated in my PM to you...
Since they are all apart now, do you have the original build sheet showing the parts and labor in the block? Maybe even a dyno printout?

 

PM'ing

 

PM sent on BMR stuff

 

intrested in the BMR Torque arm. Trans mount... correct? For 700R4? Still available? If so, I'll take it, no pics needed. I'll PM you also.

 

PM SENT