I have a bunch of stuff sitting around I'd like to sell. Best offer takes it.

Aluminum valve covers, perimeter bolt pattern $30

March underdrive pulley set, crank, alternator, water pump, $100 shipped.

Mini started from summit $50

T top covers fair condition $30

Auto meter 5" tach to 8k rpm w/ shift light $100 obo

1 gal fuel cell with check valve and foam $60+ shipping

NX direct port system 200-600hp make offer

wide open throttle switch

progressive controller for the nitrous $100

misc switches for purge, bottle heater, activation, 2 step rev limiter, etc. $20 obo

I also have a complete long block that has gone 11.60's on motor. $ make offer or pm for details forged and built for the bottle

Protopline 200cc heads 7/16 screw in studs with guide plates $800+shipping or can arrange pick up

Comp Cams 306 cam $100 + shipping

hardened pushrods 0.100 longer than stock $70

ZZ4 crank and block that has been converted to 4 bolt studded main caps, oil holes chamfered, crank polished, etc. $ make offer

Comp Cams magnum pro rockers $140

Valve springs matched for the cam (can get specs if interested) $80 shipped obo

Electric water pump $80

Eagle H-beam 5.700 forged rods $150

JE custom forged nitrous pistons with total seal rings $700 new will sell for $300, these are VERY good n2o pistons that are lightweight for a foged slug.



I have a LOT of other parts and electronics so if you have a thirdgen or a dinosaur just ask and I'll look around. Trying to clean out a lot of things and all must go. Please PM here or email me at the following addy.

tharney at pbsj dot com

 

Are the rockers the 1.52 lift with a 3/8" stud? Self aligning? Do you have a part number? I'm interested in them and the pushrods...

 

same as above, but im only interested if they're not self aligning . also, how much for the digital 6?

 

Do you have any numbers on the lifters?

 

Numbers? as in part numbers?

The lifters are NOT self aligning, that's why the heads have guideplates. The studs are 7/16, NOT 3/8.

To the others who PM'd me, I've sent replies and have taken pictures. I'll get them hosted and posted tomorrow morning.

 

What kind of progressive controller? Pics, part numbers? Thanks

 

I've taken pictures and should have them up tomorrow.
The lifters are comp cams High Energy that they recommended for the cc306 cam. Summits lists them for $210 new.

The controller is a model usually used for motorcycles. It's worked really well when I tested it, and an LS1 owner was using the same one that worked well for him. I can't remember the brand name, but I'll try searching for it. I remember it was a much more cost effective set up than using the NOS brand.

Edit: I've replied to some more PMs with prices and part numbers. Thanks for everyone's patients.

PS - got it http://www.tobefast.com/schnitz-raci...er-pr-226.html

 

bump, prices are best offer guys, lets work something out.

 

How much for the progressive controller?

 

$100 shipped for the controller.

 

Electric water pump brand, hours, and price? What MSD box?

 

How much for the tach shipped to 30038

 

Hours on pump?? Honestly, I have no idea, never kept track. Less than 3k miles on all the parts though, that I'm sure of. $100 shipped for the pump sound fair?

The MSD digital 6+ with 2 step rev limiter. Retard at engine start, etc. summit has the details.

.... pictures coming.

 

$120 shipped.

 

These are replacement door hinges for 3rdgens. Never used, still in original packaging.

 

 

Thank you

 

how much for the cam shipped to 78372

 

Lets say $100+shipping. Looks like UPS wants $18.30 for shipping.

 

Interested? Or not anymore?
I'm also open to offers guys. Need to get rid of this stuff.

Pics of the N2O installed.

 

I am interested in the MSD Dig6 box. How much shipped to St Louis 63114?

 

$289 new so lets say $150 shipped

 

PM Me your PayPal Address and I will get the money to ASAP.
Thanks

 

Mudd, check your PMs.

Also sent out replies to others via PMs.

 

MSD, SPF
Door hinges SPF
Lifters, SPF

Thanks for the interest guys, still lots of parts for sale.

 

Do you still have the cam? Is it a Hyd. roller? Specs?

 

Do you have the lifters for sale? If they are new, can you post up the part number?

Thanks,

 

New or used ?
JE Part # ?

 

Yes the cam is a hydraulic roller. The part number is 07-306-8. Specs can be found on summit or the comp cams website.

Rough specs
230/244
290/307 @ .050
112 LSA

 

The pistons are used but the engine has never been sprayed. Don't have the pn on me, I'll try and get it this weekend. THanks for your interest.

 

Lifters have been sold.
Still have cylinder heads, complete
valve covers
water pump
oil pan
rods
pistons
block, crank, caps
timing chain and cover

along with everything else in the first post.

 

MSD box showed up this week. Thanks again.

 

Part # for the rods, and use time? and how much for shipping to HI 96706?
thanks
Bryan

 

will need to double check the pn but I believe they're ESP-5700S3D with 2.00 dim on the journals. Floating pin. Less than 3000 miles on them. They should look brand new when I take the bottom end apart, if not, I'll send you a picture and see what you want to do. Parts and shipping lets say $250 shipped.

 

bump.

 

Bump, I added some other parts the list and updated what was sold.

 

bump

 

do you have all the stuff for the holley 950 commander or is it just the box and what is the price

 

I only have the box and the injector harness. Not the rest of the harness. Also have the software for it. I think I sent you a PM.

 

price on 950 stuff shipped to 49031?

 

bird i checked i havent recieved a pm

 

Lets say $300 shipped to the lower 48.
Also still have the cylinder heads
rockers
pushrods
head bolts
mini starter
t-top covers
nitrous controller
bottle
solenoids
purge
fittings
fuel cell
etc.

 

bump

 

price on nitrous stuff shipped to 45601

pix on valve covers

tkcaraudio@yahoo.com

 

Sorry I haven't gotten back to you since now. What size bottle, what size line for the purge and still have the controller?
It may be easier to just email me at sage85z28@aol.com thanks.

 

WILL YOU DO 250 SHIPPED ON H BEAMS AND 306 CAM DONT WANT SERP SET UP

 

price shipped to 46385?

 

i could use the summit mini starter if it works good and stuff, if you still got it. ill send a pm

 

Do you just want the nitrous and purge solenoids? Or the entire kit w/ bottle, heater, etc.

 

bump