what dose it take to make a spark only bin
#1
Senior Member
Thread Starter
Join Date: May 2002
Location: concord New Hampshire
Posts: 569
Likes: 0
Received 0 Likes
on
0 Posts
Car: 87 iroc and 88 k2500 tbi truck
Engine: l98 and lo5
Transmission: 700 r4's babby
what dose it take to make a spark only bin
i need to figure out how i can run a carb on my truck for a few months it has a 747 ecm. i would like to keep the stock dizzy and just throw the carb on as a temp till stuff comes together. thanks ahead of times guys
#2
There is a file called 7747sprk.txt on DIY-efi.org.
Not much needs done other than turning off some DTC's.
And making a TPS bracket for your carb....
Unless you make a cable op thingie like S&P or somebody sells.
A manual choke holley looks to be reasonably easy. Just make a mount plate to go on the manual lever plate and a rod to screw into the primary throttle shaft with a flat on the other end to turn the tps. I'll be doing one in a month or two.
Not much needs done other than turning off some DTC's.
And making a TPS bracket for your carb....
Unless you make a cable op thingie like S&P or somebody sells.
A manual choke holley looks to be reasonably easy. Just make a mount plate to go on the manual lever plate and a rod to screw into the primary throttle shaft with a flat on the other end to turn the tps. I'll be doing one in a month or two.
#3
Supreme Member
Join Date: Jun 2000
Location: In reality
Posts: 7,554
Likes: 0
Received 1 Like
on
1 Post
Car: An Ol Buick
Engine: Vsick
Transmission: Janis Tranny Yank Converter
Originally posted by Z69
There is a file called 7747sprk.txt on DIY-efi.org.
And making a TPS bracket for your carb....
There is a file called 7747sprk.txt on DIY-efi.org.
And making a TPS bracket for your carb....
As I recall, it's not needed.
#4
Correct, not required IIRC from the txt file or somewhere.
Maybe it was one of your posts.
But nice to have, and I have 8D stuck in my head.
I don't recall how PE is done in 747 land.
Maybe it was one of your posts.
But nice to have, and I have 8D stuck in my head.
I don't recall how PE is done in 747 land.
#5
Supreme Member
Join Date: Jun 2000
Location: In reality
Posts: 7,554
Likes: 0
Received 1 Like
on
1 Post
Car: An Ol Buick
Engine: Vsick
Transmission: Janis Tranny Yank Converter
Originally posted by Z69
Correct, not required IIRC from the txt file or somewhere.
Maybe it was one of your posts.
But nice to have, and I have 8D stuck in my head.
I don't recall how PE is done in 747 land.
Correct, not required IIRC from the txt file or somewhere.
Maybe it was one of your posts.
But nice to have, and I have 8D stuck in my head.
I don't recall how PE is done in 747 land.
#6
Moderator
iTrader: (1)
Join Date: Mar 2002
Location: Chasing Electrons
Posts: 18,405
Likes: 0
Received 216 Likes
on
202 Posts
Car: check
Engine: check
Transmission: check
With a carb it is better to put any PE type spark in the main SA table. In this manner it can be setup to coincide with the power valve or step up rods activating (via manifold pressure).
RBob.
RBob.
#7
Supreme Member
Join Date: Feb 2002
Location: Buckhannon, WV
Posts: 2,663
Likes: 0
Received 3 Likes
on
2 Posts
Car: 84' Monte
Engine: 350
Transmission: 700-r4
Axle/Gears: ferd 9" posi 3.50 gears
I used Rbobs spark only tutorial for quite a while on my car while I got the hang of this chip tuning thing. It's quite easy. Just follow his article and it will tell you what dtc to turn off and what other parameters to play with. The tps is not needed, unless your wanting to use the TCC lock up, there is a flag that makes it MPH based but I never played with it.
Thread
Thread Starter
Forum
Replies
Last Post
92camaroJoe
Tech / General Engine
6
08-13-2015 06:07 AM