Location of stock wiring
#1
Senior Member
Thread Starter
Join Date: May 2002
Location: Gloucester,England,UK
Posts: 678
Likes: 0
Received 0 Likes
on
0 Posts
Car: '92 RS Camaro
Engine: 406ci D1SC SBC
Transmission: TH400
Axle/Gears: 9" W/Truetrac
Location of stock wiring
Im putting back the all the stock wiring after an engine swap, except all the fuel injection stuff. Problem is, i need to know the route of the wiring on the car.
Main things I need to know, are:
Where does the junction block in pic 1 locate?
Whats the route of the cable to the alternator in pic 2
Whats the route of the cables to the starter in pic 3
Main things I need to know, are:
Where does the junction block in pic 1 locate?
Whats the route of the cable to the alternator in pic 2
Whats the route of the cables to the starter in pic 3
#2
Member
iTrader: (3)
Join Date: Jul 2009
Location: Ontario, Canada
Posts: 409
Likes: 0
Received 0 Likes
on
0 Posts
Car: 86 IROC
Engine: 350 Vortec TPI
Transmission: 700R4
Axle/Gears: BW 3.27
Re: Location of stock wiring
The power block goes on the passanger side of the rad where the fan relay goes
The alt cable depends on what style you have. Vblet (passanger side alt mount) is straight up from the frame rail. serp system, Driver side mount, need to confirm, but does it go straight across the motor?
Starter wires can go one of three ways depending on length. The first is along the frame rail down the k member, hugging the motor to the starter, second is down the back of the motor to the starter, or the third is along the intake down the front of the motor to the k member, then back to the starter hugging the block. Believe the last way is the normal TPI way with a serp system.
The alt cable depends on what style you have. Vblet (passanger side alt mount) is straight up from the frame rail. serp system, Driver side mount, need to confirm, but does it go straight across the motor?
Starter wires can go one of three ways depending on length. The first is along the frame rail down the k member, hugging the motor to the starter, second is down the back of the motor to the starter, or the third is along the intake down the front of the motor to the k member, then back to the starter hugging the block. Believe the last way is the normal TPI way with a serp system.
#3
Senior Member
Thread Starter
Join Date: May 2002
Location: Gloucester,England,UK
Posts: 678
Likes: 0
Received 0 Likes
on
0 Posts
Car: '92 RS Camaro
Engine: 406ci D1SC SBC
Transmission: TH400
Axle/Gears: 9" W/Truetrac
Re: Location of stock wiring
Its a serpentine set up. Have ya got any pictures?
#4
Senior Member
Thread Starter
Join Date: May 2002
Location: Gloucester,England,UK
Posts: 678
Likes: 0
Received 0 Likes
on
0 Posts
Car: '92 RS Camaro
Engine: 406ci D1SC SBC
Transmission: TH400
Axle/Gears: 9" W/Truetrac
Re: Location of stock wiring
The reason Im asking, is all the wiring was pulled to one side when the old motor came out, I did have some pics, but cant find them? The wiring doesnt seem long enough to where I thought it would go
#5
Member
iTrader: (3)
Join Date: Jul 2009
Location: Ontario, Canada
Posts: 409
Likes: 0
Received 0 Likes
on
0 Posts
Car: 86 IROC
Engine: 350 Vortec TPI
Transmission: 700R4
Axle/Gears: BW 3.27
Re: Location of stock wiring
I dont have any picks as mine is a v belt setup ('86). I have an 89 harness that I plan to put in the car with a serp setup. The starter wires go from the c100 across the back of the motor, to the front of the motor, then down the front hugging the block to the starter. In there there are also the knock and one other wire (you dont need those for a carb setup).
As for the power block, it is on the side of the rad beside the battery on the passanger side. I will see if I can dig up a picture.
As for the power block, it is on the side of the rad beside the battery on the passanger side. I will see if I can dig up a picture.
Thread
Thread Starter
Forum
Replies
Last Post