GMPP LT4 Full Roller Rockers 1.6 ratio
07-25-2006, 11:27 AM
#1
GMPP LT4 Full Roller Rockers 1.6 ratio
These are the roller rockers made by crane for GM for the 1996 LT4 and these are the same ones that come in the LT4 HOT Cam kit. These have 3/8 stud holes. GM part number 12370839. GM parts direct lists these for $282.76. These were used for less than 30K miles. They are stored in oil. No wear marks on them.
Check out my username on the feedback board. I don't sell junk. These are off of my motor. I'm switching to a stock LT1 so I reall won't be needing any of my performance parts.
$200 FREE SHIPPING to the lower 48. Paypal or USPS Money Orders.
Pics to come
Check out my username on the feedback board. I don't sell junk. These are off of my motor. I'm switching to a stock LT1 so I reall won't be needing any of my performance parts.
$200 FREE SHIPPING to the lower 48. Paypal or USPS Money Orders.
Pics to come
07-28-2006, 05:30 PM
#5
Supreme Member
iTrader: (7)
Join Date: Aug 2005
Location: Ohio, near columbus
Posts: 1,068
Likes: 0
Received 1 Like
on
1 Post
Car: 89 iroc-z
Engine: 305tpi
Transmission: wc-t5
Axle/Gears: 10 bolt 3.08 posi (4 now)
i'm interested but, need to sorta double check to make sure it's what i need, also need pics
And if it's what i need (checking right after i post this) will you let them go for 175$ shipped.
And if it's what i need (checking right after i post this) will you let them go for 175$ shipped.
Trending Topics
08-02-2006, 04:39 PM
#8
Senior Member
Join Date: Jan 2006
Location: League City, TX
Posts: 720
Likes: 0
Received 1 Like
on
1 Post
Car: 90 Formula -- tot resto in progress
Engine: 350
Transmission: 700R4 w/ 2500 stall, by Owen @ ARD
Axle/Gears: 3.23 posi disc
Are they still available?
If so, do you know if they will fit under the standard centerbolt valve covers?
I know there's clearance problems with aftermarket 1.6 lifters & these v-c's.
thanks,
kk
If so, do you know if they will fit under the standard centerbolt valve covers?
I know there's clearance problems with aftermarket 1.6 lifters & these v-c's.
thanks,
kk
10-05-2007, 06:45 PM
#14
Supreme Member
iTrader: (3)
Join Date: Jan 2006
Location: Flowood,MS
Posts: 1,489
Likes: 0
Received 0 Likes
on
0 Posts
Car: 87 IROC Z
Engine: 5.7 L98 TPI
Transmission: 700r4,2500 stall
Axle/Gears: G80,10 bolt 3.42's
Re: GMPP LT4 Full Roller Rockers 1.6 ratio
I need them if you still have them for sale.I bought some cat 1.6 stainless ones and they are crap.10,000 miles and already galling and messing up at the needle bearings.I get paid this fri and can get them then if thats ok let me know.BTW are they stainless steel or alluminum?
10-05-2007, 10:48 PM
#15
Supreme Member
iTrader: (3)
Join Date: Jan 2006
Location: Flowood,MS
Posts: 1,489
Likes: 0
Received 0 Likes
on
0 Posts
Car: 87 IROC Z
Engine: 5.7 L98 TPI
Transmission: 700r4,2500 stall
Axle/Gears: G80,10 bolt 3.42's
Re: GMPP LT4 Full Roller Rockers 1.6 ratio
ok I found the part # and they are alluminum but if they are self alligning I dont need them
Thread
Thread Starter
Forum
Replies
Last Post
Hotrodboba400
Firebirds for Sale
3
12-10-2019 07:07 PM
New2Chevy
Engine/Drivetrain/Suspension Parts for Sale
2
09-28-2015 12:35 AM
UltRoadWarrior9
Transmissions and Drivetrain
3
09-02-2015 08:24 PM
