Vanguard

iTrader: (1)

I am selling a complete supercharger kit which will fit the 85-87 tpi camaros & firebirds

I purchased it from a member on this board over 8 years ago but never bolted it to my car. Even though person I bought it from said it worked great, I decided to pull it apart and freshen it up.

The member was right, it was in good condition. However, I went ahead and replaced all the internal components like the bearings, seals, ball bearings, oil pump and filter. I also set the rotating torque on the high side as per a recomendation from paradise wheel. Paradise wheel services the older paxton stuff and they gave me lots of help during the rebuild.


Here is what is included:
sn89 blower, rebuilt
(2) aluminum intake elbows, setup for water injection
(8) belts
crank pulley with reinforcement
mounting bracket with bolts & support
intake duct with elbow
spare parts from rebuild
Paxton supercharger service manual
Paxton installation guide for 85-87 tpi firebird
Paxton owner rebuild guide for SN89 & 92, by CUNDN racing
Hot Rod article from July 88 - booster shot, showcasing the paxton on several f bodys

I am looking to get $600 for everything

give me a call and lets talk, Eric 623-521-0817

Vanguard

iTrader: (1)

more pics

Vanguard

iTrader: (1)

and more pics

Vanguard

iTrader: (1)

Looks like $800 is not working

Anyone for $700 ??

AmorgetRS

iTrader: (6)

Question for ya - what does this need to be ready to run?

BigBadGTA

I suppose you couldn't make this work on an 88 because 88 was the first year for the serpentine set up correct? If it would work I would be extremely interested. How much boost does this produce?

Vanguard

iTrader: (1)

The Paxton install manual recommends positioning the maf sensor where the airflow can sits and putting an airfilter under neath the inner fender.

The attached files should help understand the routing.

I am not sure I would go with this method but thats just me.

Aside from the air cleaner issue, the remaining parts required to complete the install are a few hose couplings with hose clamps, bolts for the crank pulley, other misc bolts.

Note that I do not have the water injection portion of this kit.

As far as boost levels, this article says the max boost level is 5 to 6 psi at 5000 rpm. If you rev beyond this rpm, the larger (3) ball bearings begin to slip on the races. This is the reason why I set the rotating torque of the blower on the high side.

Vanguard

iTrader: (1)

Here is another part of that same article. It talks about a paxton equipped 350 tpi GTA running the 13.67 at 102 mph quarter mile. 0-60 was 4.7 seconds.

Also,

unfortunatley this kit will not fit 88 and up f-bodys

Vanguard

iTrader: (1)

new price, down to $600

DIRTY JERZY

Its to bad it won't fit a 89 I am thinking of turning the formula I just got into the car I had in highschool.

Vanguard

iTrader: (1)

bump

Vanguard

iTrader: (1)

new price, I need to move this

anesthes

iTrader: (12)

With a pulley some flat stock and some spacers it will work.

I've run some pretty crazy belt routing on my setups.

-- Joe

Stangski09

iTrader: (10)

I think you could run this on an 88 and up, especially if you have AC delete. You could just switch your battery and charcoal cannsiter and youre good to go. If you have AC, I think you could fab up a new bracket too work.

Vanguard

iTrader: (1)

Here is a picture of this blower installed on an 88 pontiac.

hawkins

will this fit on an 1988 iroc? and do you have the brackets for it ?

Vanguard

iTrader: (1)

the blower will work on an 88 but you will need another bracket for mounting

Since paradise wheel bought the rights to the older paxton stuff, they may be able supply the bracket.

Here is their contact info:

Paradise Wheels
Craig Conley
920 Rancheros Drive Suite E
San Marcos, CA 92069
Phone: 760-740-0954
Fax: 760-740-0956