luckydog0_18

Hello, ok so I pulled my 305 tpi engine out of my 1986 iroc z-28 with 51,280 miles the number 5 rod bearing started making noise so I had a 350 built and am not keeping anything from the 305 except the block. If it's ok to do it this way,cool. Let me know what you need and I'll let you know how much and if it's available. I am located in Pa 15322 zip, but can try to figure shipping if needed. Thank you.

luckydog0_18

no one needs any parts? have a lot. heads,rods, push rods, pistons, oil pump, oil pan, tpi system, ect.... thank you.

ApolloX64

iTrader: (1)

I would love to get my hands on those heads, but it'd probably cost an arm and a leg to ship 'em up to me lol.

NC-88

How much for the oil pan shipped to 60922? And I have a noob question, it should fit my GEN I small block right?

Thanks

luckydog0_18

I dont see why it wouldnt fit, but to be sure what year and engine do you have? Ill double check for you.

luckydog0_18

Where would you want them shipped to?

Joel07

iTrader: (1)

How much for the heads shipped to zip code 27572?

Joel07

iTrader: (1)

Oh, and the oil pans are different depending on if you have a 1 piece or 2 piece rear main seal BTW...

NC-88

Block is 3970010, 1969-79, 2 piece rear main seal...

luckydog0_18

ahh thanks for that info I never even thought about that.

luckydog0_18

I didnt realize that the 2 pcs and 1 pcs was different oil pans as stated by joel07
and mine was a 1 pcs so with that said I am assuming if will not fit, sorry.

luckydog0_18

give me a day or 2 to get a price for you, if thats ok with you. now they really dont need rebuilt but i would put new valve seals in. but i will work on the price for you right away.

Joel07

iTrader: (1)

No problem, not in a huge hurry, and no problem on the valve seals. They'll get some port work and a 3 angle valve job anyway.

Joel07

iTrader: (1)

Actually cancel that anyway, just re-read that yours is a 86, I want the 87+ heads anyway. Thanks though...

oscarfromla

iTrader: (9)

Is your oil pan for a 1 pc or 2 pc RMS? I need a good condition one for a 1 pc, my block is 87 or 88. If it is for a 1 pc RMS, how much shipped to 90248 and do you have a picture?

luckydog0_18

sorry it took a couple days to respond,(I'm not getting notification when someone responds) I can take a picture, it is for a 1 piece.

glangfor

I'm looking for the complete Diverter Valve setup, EGR Solonoid and Bracket. Thanks..

Locations is 28052

luckydog0_18

Let me check to make sure, you want EGR solenoid not valve?

glangfor

Yes the solenoid. It looks like it mounts on the same bracket as the coil. I'm needing that bracket also if you have it. And of course the Diverter valve that is coming off of the smog pump. Thanks...Gerald

luckydog0_18

Do you have a tpi car? I ask because my coil is on top of my distributor I have a HEI distributor.

evilemokid94

iTrader: (6)

oil filter adapter, serpentine setup, and motor mounts?

glangfor

I'm in the process of building my first one, so I'm buying a few parts at a time to get it together. I could consider the HEI unit if the price is right though...

Motown

Passenger side exhaust manifold with AIR tubes intact? Let me know if you still have it.

zeppelinrok75

How much for full tpi system shipped to 22911? Thanks

luckydog0_18

here is a picture of it when i took my exhaust off one of the bolts came out. I know that no biggie but I wanted to tell you. in case you cant see it.

luckydog0_18

what all do you consider full tpi set-up?

luckydog0_18

what do you consider a full complete tpi set-up?

luckydog0_18

here is a picture of my diverter valve

WILL85IROC

do u still have the fuel rails???

luckydog0_18

yes

85 Z28

how much for the tpi system with harness and computer shipped to 33312

luckydog0_18

Im not getting rid of the harness,sorry.

luckydog0_18

here you go. heres a picture with the passenger side.