[NY] Various Engine/Drivetrain Parts [Camaro]
#1
Junior Member
Thread Starter
Join Date: Mar 2013
Location: Amsterdam, NY
Posts: 98
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1988 Chevrolet Camaro IROC-Z
Engine: 408 LSx
Transmission: T56 Magnum
Axle/Gears: 3.73 10-Bolt Detroit TrueTrac
Various Engine/Drivetrain Parts [Camaro]
A continuation of my series of threads. Looking for these parts for my '88 IROC/engine build.
Headers for Gen I SBC's (prefer long tubes)
600-700CFM carb w/ mechanical secondaries (electric choke, Holley preferred)
Forged 350 crankshaft (mine is scored, previous owner spun a bearing, debating if turning it would be cheaper)
4th gen rear end w/ disc brakes
10-bolt 3.73 posi unit
That's all for now, I'll update this depending on what I get and what I remember I need.
Please check my other threads:
Interior:
https://www.thirdgen.org/forums/inte...ts-camaro.html
Exterior:
https://www.thirdgen.org/forums/exte...ior-parts.html
Headers for Gen I SBC's (prefer long tubes)
600-700CFM carb w/ mechanical secondaries (electric choke, Holley preferred)
Forged 350 crankshaft (mine is scored, previous owner spun a bearing, debating if turning it would be cheaper)
4th gen rear end w/ disc brakes
10-bolt 3.73 posi unit
That's all for now, I'll update this depending on what I get and what I remember I need.
Please check my other threads:
Interior:
https://www.thirdgen.org/forums/inte...ts-camaro.html
Exterior:
https://www.thirdgen.org/forums/exte...ior-parts.html
#2
Member
iTrader: (6)
Join Date: Apr 2013
Posts: 385
Likes: 0
Received 0 Likes
on
0 Posts
Car: 91 ws6
Engine: Carb'd 334 stroker
Transmission: T5
I have 3 long tubes, no idea what brand. Two drivers side headers, both in good shape, one pass side. Pass side..had a hole, I welded it shut. The collector flange looks like the previous owner tried eating it; its..ripped off. Could weld on the collector from the third header tho. All are a bit rusty..
Did not fit properly on my 86 t/a, but fit fantastic when flipped upside down and through the hood!
Asking $30+shipping from southeast ks
Did not fit properly on my 86 t/a, but fit fantastic when flipped upside down and through the hood!
Asking $30+shipping from southeast ks
#3
Junior Member
Thread Starter
Join Date: Mar 2013
Location: Amsterdam, NY
Posts: 98
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1988 Chevrolet Camaro IROC-Z
Engine: 408 LSx
Transmission: T56 Magnum
Axle/Gears: 3.73 10-Bolt Detroit TrueTrac
Re: Various Engine/Drivetrain Parts [Camaro]
I have 3 long tubes, no idea what brand. Two drivers side headers, both in good shape, one pass side. Pass side..had a hole, I welded it shut. The collector flange looks like the previous owner tried eating it; its..ripped off. Could weld on the collector from the third header tho. All are a bit rusty..
Did not fit properly on my 86 t/a, but fit fantastic when flipped upside down and through the hood!
Asking $30+shipping from southeast ks
Did not fit properly on my 86 t/a, but fit fantastic when flipped upside down and through the hood!
Asking $30+shipping from southeast ks
#6
Junior Member
iTrader: (1)
Join Date: Oct 2014
Location: West Chicago land
Posts: 6
Likes: 0
Received 0 Likes
on
0 Posts
Car: 03 cummins and 84 se firebird
Engine: Sbc
Re: Various Engine/Drivetrain Parts [Camaro]
Hate to revive a dead thread but I have a set of long tubes and a full exhaust for sale. I also have a 500hp gen 1 sbc 383 for sale. Let me know if u need anything
Thread
Thread Starter
Forum
Replies
Last Post