has anyone ever bought an engine from engine factory?
05-11-2001, 10:31 PM
#1
Member
Thread Starter
Join Date: Jun 2000
Location: All over Virginia
Posts: 228
Likes: 0
Received 0 Likes
on
0 Posts
has anyone ever bought an engine from engine factory?
Engine Factory, what do you guys think of the motor minus power options? If you do not want to go to the link here is the setup:
350 CHEVY 4 BOLT MAIN IN STOCK READY TO SHIP
-4 BOLT MAIN BLOCK
-CAST IRON GM 350 CRANKSHAFT
-SHOT PEENED STRESS RELIEVED CONNECTING RODS, WITH 190,000 PSI ROD BOLTS
-HEAVY DUTY PISTONS
-SPEED PRO MOLY RINGS
-SPEED PRO 3000 CAM GOOD IDLE MEGA TORQUE
-EDELBROCK DOUBLE ROLLER TIMING SET
-HEAVY DUTY TRIMETAL ENGINE BEARINGS
-HIGH VOLUME OIL PUMP
-SCREW IN ROCKER STUDS
-NEW WORLD PRODUCTS SPORTSMAN II HEADS WITH 64cc COMBUSTION CHAMBERS
-200cc INTAKE RUNNERS
-NEW 2.02" STAINLESS STEEL INTAKE VALVES
-NEW 1.60" STAINLESS EXHAUST VALVES
-HARD SEATS AND GUIDES FOR UNLEADED FUEL
-NEW PUSHRODS, GUIDE PLATES, AND ROCKER ARMS
-NEW OIL PAN, TIMING COVER, CHROME VALVE COVERS
-NEW GM HARMONIC BALANCER DAMPER
-NEW FLEXPLATE FOR AUTO TRANS (STD TRANS FLYWHEEL EXTRA)
BALANCED, BLUE PRINTED ASSEMBLED AND PAINTED
$2,775.00
upgrades=
Dart Cylinder Heads $150.00
1.6 ROLLER TIP ROCKER ARMS $130.00
Will the cam work with a TPI setup and do you think that is a good deal?
350 CHEVY 4 BOLT MAIN IN STOCK READY TO SHIP
-4 BOLT MAIN BLOCK
-CAST IRON GM 350 CRANKSHAFT
-SHOT PEENED STRESS RELIEVED CONNECTING RODS, WITH 190,000 PSI ROD BOLTS
-HEAVY DUTY PISTONS
-SPEED PRO MOLY RINGS
-SPEED PRO 3000 CAM GOOD IDLE MEGA TORQUE
-EDELBROCK DOUBLE ROLLER TIMING SET
-HEAVY DUTY TRIMETAL ENGINE BEARINGS
-HIGH VOLUME OIL PUMP
-SCREW IN ROCKER STUDS
-NEW WORLD PRODUCTS SPORTSMAN II HEADS WITH 64cc COMBUSTION CHAMBERS
-200cc INTAKE RUNNERS
-NEW 2.02" STAINLESS STEEL INTAKE VALVES
-NEW 1.60" STAINLESS EXHAUST VALVES
-HARD SEATS AND GUIDES FOR UNLEADED FUEL
-NEW PUSHRODS, GUIDE PLATES, AND ROCKER ARMS
-NEW OIL PAN, TIMING COVER, CHROME VALVE COVERS
-NEW GM HARMONIC BALANCER DAMPER
-NEW FLEXPLATE FOR AUTO TRANS (STD TRANS FLYWHEEL EXTRA)
BALANCED, BLUE PRINTED ASSEMBLED AND PAINTED
$2,775.00
upgrades=
Dart Cylinder Heads $150.00
1.6 ROLLER TIP ROCKER ARMS $130.00
Will the cam work with a TPI setup and do you think that is a good deal?
05-25-2001, 08:25 PM
#3
Junior Member
Join Date: May 2001
Location: Aliso Viejo, CA USA
Posts: 50
Likes: 0
Received 0 Likes
on
0 Posts
Thread
Thread Starter
Forum
Replies
Last Post
86IROC112
Engine/Drivetrain/Suspension Wanted
7
09-07-2015 01:37 PM
