Exhaust and subframe connectors
#1
Member
Thread Starter
Join Date: May 2002
Location: sweden
Posts: 260
Likes: 0
Received 0 Likes
on
0 Posts
Car: Firebid Cab-92/1989 TTA
Engine: 383 HSR TPI
Transmission: TH700r4
Axle/Gears: 4.10
Exhaust and subframe connectors
Hi
How are you doing to make room for the exhaust when you have subframe connectors Installed?
Have a 1989 TTA
How are you doing to make room for the exhaust when you have subframe connectors Installed?
Have a 1989 TTA
#2
Supreme Member
Re: Exhaust and subframe connectors
I have the UMI subframe connectors
http://umiperformance.com/catalog/in...roducts_id=127
No problems with the catback. The Y pipe was fine when I use 2." inch piping but when I went to 3" I had to cut and angle it a bit down by the brace to get it to fit.
http://umiperformance.com/catalog/in...roducts_id=127
No problems with the catback. The Y pipe was fine when I use 2." inch piping but when I went to 3" I had to cut and angle it a bit down by the brace to get it to fit.
#3
Supreme Member
Join Date: Jul 1999
Location: Ahead of you...
Posts: 2,752
Likes: 0
Received 6 Likes
on
5 Posts
Car: 1984 LG4 Camaro
Engine: 350 Roller Motor
Transmission: Level 10 700R4
Axle/Gears: Strange 12 bolt 3.42
Re: Exhaust and subframe connectors
The Spohn connectors give factory-like clearance to the y-pipe, which is where 90% of the problem is with subframes.
#5
Member
Thread Starter
Join Date: May 2002
Location: sweden
Posts: 260
Likes: 0
Received 0 Likes
on
0 Posts
Car: Firebid Cab-92/1989 TTA
Engine: 383 HSR TPI
Transmission: TH700r4
Axle/Gears: 4.10
Re: Exhaust and subframe connectors
Ok
I have the Competition Engineering#247-3111
Subframe Connectors
1982-92
And its written that they dont fit facory exhaust😫
Think i just have to start to cut into the subframe
Didn t notice that when i bougth them.
I have the Competition Engineering#247-3111
Subframe Connectors
1982-92
And its written that they dont fit facory exhaust😫
Think i just have to start to cut into the subframe
Didn t notice that when i bougth them.
#7
Member
Thread Starter
Join Date: May 2002
Location: sweden
Posts: 260
Likes: 0
Received 0 Likes
on
0 Posts
Car: Firebid Cab-92/1989 TTA
Engine: 383 HSR TPI
Transmission: TH700r4
Axle/Gears: 4.10
Re: Exhaust and subframe connectors
Well thats not going to happend,i dont think you cant buy those in sweden and shipping is very expensive.
I going to modify the one i have on the car and hope they still do some good,car make close to 600fwhp so think i need them
I going to modify the one i have on the car and hope they still do some good,car make close to 600fwhp so think i need them
Trending Topics
#9
Member
Thread Starter
Join Date: May 2002
Location: sweden
Posts: 260
Likes: 0
Received 0 Likes
on
0 Posts
Car: Firebid Cab-92/1989 TTA
Engine: 383 HSR TPI
Transmission: TH700r4
Axle/Gears: 4.10
Re: Exhaust and subframe connectors
I vill not cut on subframe just going to flat out a pice of 4 inch on the connectors,they are already bolted to the car and fits fine exept for exhaust clerence
Thread
Thread Starter
Forum
Replies
Last Post