power steering pump pulley removal
#1
Member
Thread Starter
Join Date: Aug 2007
Location: longisland, ny
Posts: 104
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1988 Trans am
Engine: 358
Transmission: 700R4
Axle/Gears: 3.73
power steering pump pulley removal
So the only thing left I need to transfer from my 305 to my new 355 is my power steering pump but can't figure out how to remove the pulley to get to the bolts that are underneath. Any help would be appreciated, don't wanna go out and get a pulley puller and ruin the pulley if I can avoid it. Thanks for the help
#3
Senior Member
iTrader: (3)
Re: power steering pump pulley removal
I have a steering wheel puller kit with a bunch of attachments (in an unknown location in my garage at the moment). Anyone know if these kits are universal? Meaning, will some of the attachments in a S.W. kit work on a P.R. kit? I'm just curious.
#4
Supreme Member
iTrader: (4)
Re: power steering pump pulley removal
No you have to get a special puller. That thing looks like an installer more than a puller. You usually get a kit that has both. They both use that same giant bolt.
http://www.amazon.com/OTC-7185-Power.../dp/B0002SRG3E
That's a puller. It has two half clamshells that you put around the snout of the pulley. Then you put the ring over it to hold them together. Put a wrench on the hex head at the end of the bolt, and put another on the assembly holding the pulley snout, and start crankin that bad boy off. It's a pretty annoying job. Those things are on there TIGHT.
rent it from your local auto parts place so you dont have to actually buy one.
http://www.amazon.com/OTC-7185-Power.../dp/B0002SRG3E
That's a puller. It has two half clamshells that you put around the snout of the pulley. Then you put the ring over it to hold them together. Put a wrench on the hex head at the end of the bolt, and put another on the assembly holding the pulley snout, and start crankin that bad boy off. It's a pretty annoying job. Those things are on there TIGHT.
rent it from your local auto parts place so you dont have to actually buy one.
#6
Senior Member
iTrader: (3)
Join Date: Aug 2008
Location: Memphis, TN
Posts: 614
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1992 z28 Purple Haze
Engine: 5.7L Tuned Port Injection
Transmission: 700R4
Axle/Gears: 3.23 both spinning
Re: power steering pump pulley removal
Infernal is right TIGHT and then some! Have some WD-40 or PB Blaster handy. Going back on is fun too.
#7
Member
Thread Starter
Join Date: Aug 2007
Location: longisland, ny
Posts: 104
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1988 Trans am
Engine: 358
Transmission: 700R4
Axle/Gears: 3.73
Re: power steering pump pulley removal
Thanks for the help guys, its been bothering me for a few days lol
Trending Topics
#8
Moderator
Join Date: Jul 1999
Location: 51°N 114°W, 3500'
Posts: 17,110
Likes: 0
Received 120 Likes
on
101 Posts
Car: 87 IROC L98
Engine: 588 Alcohol BBC
Transmission: Powerglide
Axle/Gears: Ford 9"/31 spline spool/4.86
Re: power steering pump pulley removal
The second picture looks much better. It's a special puller that slips over the collar on the pulley. A generic puller will not remove the pulley no matter how much you try, without damaging the pulley.
As mentioned above, you can usually rent the tool. An impact gun makes using pullers a lot easier but lots of muscles can also do the job. It just takes longer.
As mentioned above, you can usually rent the tool. An impact gun makes using pullers a lot easier but lots of muscles can also do the job. It just takes longer.
Thread
Thread Starter
Forum
Replies
Last Post
colton_carlson
Firebirds for Sale
7
03-08-2019 12:21 PM
backtothe80s
Suspension and Chassis
33
09-05-2015 12:39 AM
Street Lethal
Engine/Drivetrain/Suspension Parts for Sale
0
08-12-2015 11:33 AM