Third Generation F-Body Message Boards

 
Page 1 of 2
1
2
Search: Posts Made By: davila0115
Showing results 1 to 50 of 88
Search took 0.10 seconds.
Forum: V6
10-12-2014, 02:40 PM
Replies: 12
Views: 2,787
Posted By davila0115

Re: 3.1L crank, but no start.

Checked fuel pressure. Have 42 psi while cranking... Def have spark. Pulled a plug. Left it plugged in to the spark plug boot. And I get a nice bright spark while cranking... tried a new air charge...
Forum: V6
10-10-2014, 09:12 AM
Replies: 12
Views: 2,787
Posted By davila0115

Re: 3.1L crank, but no start.

i see spark. maybe its week? i would hate to buy another ign coil just for nothing to change... and i agree. you would get something. sputtering, backfire, chugging, something...
Forum: V6
10-09-2014, 07:35 PM
Replies: 12
Views: 2,787
Posted By davila0115

Re: 3.1L crank, but no start.

So i got the ign module tested it shows fine.... i tried a new Air inlet charge temp sensor. Still wont start... does the fuel pump run until it hits a certain pressure? seems after i try to crank...
Forum: V6
10-07-2014, 08:59 PM
Replies: 12
Views: 2,787
Posted By davila0115

Re: 3.1L crank, but no start.

When it was doing what? I had an engine code at one time prolly but it was after i unplugged the air temp sensor. So i am sure it was from that. but in the process to get the car started again i...
Forum: V6
10-07-2014, 06:34 PM
Replies: 12
Views: 2,787
Posted By davila0115

Re: 3.1L crank, but no start.

Won't start with starter fluid. All fuses good under the dash. Fuse on the passenger side inner fender is good. How can you ohm test the injectors without pulling the upper plenum? Still have spark...
Forum: V6
10-07-2014, 09:27 AM
Replies: 12
Views: 2,787
Posted By davila0115

Re: 3.1L crank, but no start.

The injectors are like 2 months old. Got them from Southbay. Full set. just installed 2 weeks ago or so. Injector fuses? are those under the dash? I did not know there were fuse(s) for them. I will...
Forum: V6
10-06-2014, 07:30 PM
Replies: 12
Views: 2,787
Posted By davila0115

3.1L crank, but no start.

OK i will try and make this short. Car was running last night, took it for 30+ miles drive with a stop in between. Got it home parked it. Woke up to take wife to breakfast got in car. it started...
Forum: Engine/Drivetrain/Suspension Parts for Sale
08-25-2014, 02:54 PM
Replies: 2
Views: 443
Posted By davila0115

Re: a/c assembly

Do you have pictures of the lines? I am looking mainly for the short hardline from the condenser to the evaporator?
Forum: V6
08-25-2014, 02:21 PM
Replies: 1
Views: 540
Posted By davila0115

A/C Replacement Woes

Hello everyone,

So I have finally decided to get the A/C running in my 92 3.1L Camaro.... When I got the car somehow the PO broke the short hard line (low side) and it was still attached but...
Forum: Interior Parts for Sale
04-22-2013, 09:07 AM
Replies: 40
Views: 1,318
Posted By davila0115

Re: parting a 1991 Z28 hardtop

Fog light switch / Blank panel for that area? Shipped to 46375. Thanks
Forum: Electronics
04-18-2013, 12:29 PM
Replies: 3
Views: 6,386
Posted By davila0115

Angel Halo Headlight Conversion Kit

Just headlights, no halos.

I still have to install the front clear markers, and the clear side markers. So i will keep everyone posted on pictures for those. Thanks.
Forum: Electronics
04-18-2013, 12:28 PM
Replies: 3
Views: 6,386
Posted By davila0115

Angel Halo Headlight Conversion Kit

Here are the Rest of the pictures with everything running....

Just halos...

Halos and parking lights...

Everything on...
Forum: Electronics
04-18-2013, 12:25 PM
Replies: 3
Views: 6,386
Posted By davila0115

Angel Halo Headlight Conversion Kit

So when i looked around i didn't find much info on the board. Just as far as this specific kit. So I figured I would do a little write up. (First write up on anything lol)

First off i picked up...
Forum: NW Indiana and South Chicago Suburb
04-12-2013, 09:26 AM
Replies: 38
Views: 1,154
Posted By davila0115

Re: Bill's Upgrade thread, OR... My Butt hurts.

Yeah, I have this Trans jack also. http://tinyurl.com/c8vdv4c Does well for the few times you use it.. Also is really handy for dropping gas tanks... Put in a few Th350's with it..
Forum: NW Indiana and South Chicago Suburb
04-11-2013, 02:30 PM
Replies: 38
Views: 1,154
Posted By davila0115

Re: Bill's Upgrade thread, OR... My Butt hurts.

Where are you located at? Have a price on the LCA's? I live in Schererville 46375. Thanks
Forum: Mid-West Region
04-11-2013, 02:20 PM
Replies: 18
Views: 890
Posted By davila0115

Re: Any Indiana guys here?

NWI for me... Schererville.... 8-)
Forum: Interior Parts for Sale
03-19-2013, 06:29 AM
Replies: 27
Views: 1,350
Posted By davila0115

Re: Parting out a 91 Camaro

Interested in the Center console armrest, full dash pad, the blank plate for the fog lights, ashtray cover flip up, auto shift plate, power door lock switche(s), and possible the front lower grill...
Forum: Engine/Drivetrain/Suspension Parts for Sale
06-12-2012, 02:44 PM
Replies: 28
[ID] A/C System
Views: 704
Posted By davila0115

Re: A/C System

PM SENT.
Forum: Engine/Drivetrain/Suspension Parts for Sale
06-12-2012, 11:50 AM
Replies: 28
[ID] A/C System
Views: 704
Posted By davila0115

Re: A/C System

How much for the smaller line with the red sensor on it? Shipped to 46375. Thanks.
Forum: NW Indiana and South Chicago Suburb
05-22-2012, 11:47 AM
Replies: 30
Views: 1,139
Posted By davila0115

Re: Nw In/Chicago ThirdGen Fest ??????????

Going to make this Decal later.. thought it might be fun to slap it on for the weekend.. HAHA:nod:
Forum: Engine/Drivetrain/Suspension Parts for Sale
05-21-2012, 02:43 PM
Replies: 15
Views: 646
Posted By davila0115

Re: Misc Engine Parts - 1991 V6

Not to be a pest, but you only have the parts listed in the first post. So no A/c Lines? Worth a shot to throw some money at you and fix my problem haha
Forum: NW Indiana and South Chicago Suburb
04-30-2012, 11:01 AM
Replies: 30
Views: 1,139
Posted By davila0115

Re: Nw In/Chicago ThirdGen Fest ??????????

I will be going,... i have no show car, but i dont think that the point of this gathering... im from schererville...
Forum: NW Indiana and South Chicago Suburb
04-12-2012, 10:45 AM
Replies: 94
Views: 3,725
Posted By davila0115

Re: Anyone Want to start a Thirdgen Club in Northwest Indiana?

Yeah it was nice to see another Fellow 3rd Gen from the forum in the area.. A lil disappointing on the turn out but its a start.. haha. I am def going to Third Gen Fest 12' This year. registered and...
Forum: NW Indiana and South Chicago Suburb
04-07-2012, 02:39 PM
Replies: 94
Views: 3,725
Posted By davila0115

Re: Anyone Want to start a Thirdgen Club in Northwest Indiana?

Oh ok, i thought all week it was Schererville.. not a prob for me. but does everyone else know its merrillville and NOT schererville?...
Forum: NW Indiana and South Chicago Suburb
04-07-2012, 10:20 AM
Replies: 94
Views: 3,725
Posted By davila0115

Re: Anyone Want to start a Thirdgen Club in Northwest Indiana?

So are we still on for today at 6pm at hooters in Schererville?... Looking forward to seeing some fellow thirdgen rides!
Forum: NW Indiana and South Chicago Suburb
04-02-2012, 07:49 AM
Replies: 94
Views: 3,725
Posted By davila0115

Re: Anyone Want to start a Thirdgen Club in Northwest Indiana?

I think i can make it. i dont have any tenative plans as of now. 6-7pm Sounds good to me... Where is everyone in this post at?...lol Time to meet up finally ppl!
Forum: V6
03-26-2012, 07:49 AM
Replies: 90
Views: 8,696
Posted By davila0115

Re: 3.1L V6 10mpg? I just dont understand....

So i got the car tested. I pulled the EGR block-off plate off the engine bc i started getting the SES light poppin on from it being blocked.. and if that would have popped on during the emission...
Forum: V6
03-22-2012, 02:28 PM
Replies: 90
Views: 8,696
Posted By davila0115

Re: 3.1L V6 10mpg? I just dont understand....

So i tested the Vacuum and it was at 18" at idle, car fully warmed up idle at 700rpm. Need to get the car emission tested soon. Wondering if this EGR plate is going to hurt the exhaust #'s they are...
Forum: NW Indiana and South Chicago Suburb
03-21-2012, 07:53 AM
Replies: 94
Views: 3,725
Posted By davila0115

Re: Anyone Want to start a Thirdgen Club in Northwest Indiana?

I am down still, Well it depends on if we want to all go to a cruise night, or just strict Third Gens hanging out in a parking lot, or a diner lot or something. I think Schererville would be nice for...
Forum: V6
03-16-2012, 03:03 PM
Replies: 90
Views: 8,696
Posted By davila0115

Re: 3.1L V6 10mpg? I just dont understand....

Nice ok.. well yeah that does make sense.

From what i have foud :

http://wiki.3400z24.com/ECM_tuning#BLM_.26_INT

The INT is the short term and the BLM is the long term... I know its wiki....
Forum: V6
03-16-2012, 07:47 AM
Replies: 90
Views: 8,696
Posted By davila0115

Re: 3.1L V6 10mpg? I just dont understand....

Ok i can understand that. But it seems like i am having a rich issue not a lean issue correct? If its not spraying enough fuel, wouldnt that make it lean? I am still waiting to get the gaskets in,...
Forum: V6
03-15-2012, 08:39 AM
Replies: 90
Views: 8,696
Posted By davila0115

Re: 3.1L V6 10mpg? I just dont understand....

Ok so then its good to assume that the injectors do not need to be replaced...

I will buy a decent vacuum gauge today or tomo and check that. Should i measure vacuum through the map line. or just...
Forum: V6
03-14-2012, 08:07 PM
Replies: 90
Views: 8,696
Posted By davila0115

Re: 3.1L V6 10mpg? I just dont understand....

So i made an EGR block-off plate for the intake side of the EGR tube. installed that today. Going to see if that improves gas mileage. I just filed up....

However i got some questions....

I am...
Forum: V6
03-12-2012, 08:36 AM
Replies: 90
Views: 8,696
Posted By davila0115

Re: 3.1L V6 10mpg? I just dont understand....

So I finally got the Coolant leak taken care of... i also figured that since every other ignition component is new, i would change out the coil. delco was about 5$ more than the MSD coil.. so i got...
Forum: V6
03-02-2012, 03:33 PM
Replies: 90
Views: 8,696
Posted By davila0115

Re: 3.1L V6 10mpg? I just dont understand....

Something that i found interesting this week, There was an unusually warm day for us up here in NWI, and i had the windows down, when i rolled them up and when u get to the top and they top, when u...
Forum: V6
03-01-2012, 01:34 PM
Replies: 90
Views: 8,696
Posted By davila0115

Re: 3.1L V6 10mpg? I just dont understand....

I have replaced the CTS, I just know the gauge is off. Need procedure to check the TPS and MAP. Obviously key on, but measurements? ranges, values?.. The IAT is clean, idk value yet. Injectors and...
Forum: V6
02-29-2012, 03:04 PM
Replies: 90
Views: 8,696
Posted By davila0115

Re: 3.1L V6 10mpg? I just dont understand....

if the thermostat was bad wouldn't the top radiator hose always be hard? (assuming it failed open which i kno the factory orig didn't.) or is it bad bc it has to get extra hot to open?... and either...
Forum: V6
02-29-2012, 02:36 PM
Replies: 90
Views: 8,696
Posted By davila0115

Re: 3.1L V6 10mpg? I just dont understand....

I know that generally the gauge is around the line that is in between the 100 and 220 marks?... i also know that once the engine is fully fully warmed up to where the fan comes on the gauge is at...
Forum: V6
02-29-2012, 12:27 PM
Replies: 90
Views: 8,696
Posted By davila0115

Re: 3.1L V6 10mpg? I just dont understand....

Well just a recap for now.. Again i appreciate all the help from everyone!...

I have replaced in the past month
-02 sensor
-new starter
-new oil pan and gasket and fresh oil
-pcv valve
-cap,...
Forum: V6
02-24-2012, 02:33 PM
Replies: 6
Views: 2,296
Posted By davila0115

Re: 3.1 Liter Bad gas Mileage

Did you ever figure this out JoeCool108?
Forum: Engine/Drivetrain/Suspension Wanted
02-21-2012, 02:52 PM
Replies: 1
Views: 350
Posted By davila0115

Metal Heater Hose / Pipe

Looking for the two (2) metal heater pipes / hoses that will swap into my 92 camaro rs v6. The stock ones are leaking. and its so tight in there that i do not like the full length heater hoses......
Forum: V6
02-13-2012, 02:22 PM
Replies: 90
Views: 8,696
Posted By davila0115

Re: 3.1L V6 10mpg? I just dont understand....

Just thinking.. around the house i have what i think is about 24 ga and some 16 ga steel. Obviously the 24 ga steel is much much easier to cut and shape. But do you think the 24ga will be thick...
Forum: V6
02-13-2012, 12:55 PM
Replies: 90
Views: 8,696
Posted By davila0115

Re: 3.1L V6 10mpg? I just dont understand....

Well ya i assumed it would advance and or move around.. figuring thats why you should unplug it to set the mechanical timing. But can i reset the ECM by just pulling that fuse? or do i have to pull...
Forum: V6
02-09-2012, 07:55 PM
Replies: 90
Views: 8,696
Posted By davila0115

Re: 3.1L V6 10mpg? I just dont understand....

So i finally got a new timing light, and checked the timing. I never mentioned i dont think that when i did the cap and rotor, that the previous owner stripped out the cap screws pretty good.. new...
Forum: Engine/Drivetrain/Suspension Parts for Sale
02-09-2012, 11:32 AM
Replies: 106
Views: 7,749
Posted By davila0115

Re: parting out 1987 gta trans am--5.7tpi

#8 on the picture above... looking for some with minimal rust... mine look like swiss cheese and i dont like how close the rubber hoses get to the exhaust manifold...

idk why the image wont...
Forum: Engine/Drivetrain/Suspension Parts for Sale
02-08-2012, 03:41 PM
Replies: 106
Views: 7,749
Posted By davila0115

Re: parting out 1987 gta trans am--5.7tpi

How about the metal heater tubes that are on the passenger side frame rail betweent he blend valve and the heater core... have those by any chance?
Forum: Engine/Drivetrain/Suspension Parts for Sale
02-08-2012, 03:39 PM
Replies: 5
Views: 411
Posted By davila0115

Re: 84. v6 t5 parting out

How about the metal heater tubes that are on the passenger side frame rail between the blend valve and the heater core... have those by any chance?
Forum: Engine/Drivetrain/Suspension Parts for Sale
02-08-2012, 03:28 PM
Replies: 18
Views: 924
Posted By davila0115

Re: GARAGE CLEAN OUT

How about the metal heater tubes that are on the passenger side frame rail betweent he blend valve and the heater core... have those by any chance?
Forum: Engine/Drivetrain/Suspension Parts for Sale
02-08-2012, 02:18 PM
Replies: 6
Views: 646
Posted By davila0115

Re: Camaro Parts (Request parts/prices)

Still have any parts? I am looking for the metal tubes for the heater core that are on the pass frame rail.. any leads? shipping cost to 46375?
Forum: V6
02-06-2012, 03:06 PM
Replies: 90
Views: 8,696
Posted By davila0115

Re: 3.1L V6 10mpg? I just dont understand....

WHOOPS DOUBLE POST....sry
Showing results 1 to 50 of 88
 
Page 1 of 2
1
2


 
Forum Jump


All times are GMT -5. The time now is 06:54 PM.