Third Generation F-Body Message Boards

Search: Posts Made By: ERockZab
Showing results 1 to 14 of 14
Search took 0.01 seconds.
Forum: LTX and LSX
11-15-2015, 08:23 PM
Replies: 14
Views: 1,194
Posted By ERockZab

Re: LS1 price

I'll do that some time this week hopefully. I'm guessing that everyone is doing the Trunion upgrade to the rockers still? Or is there something better out there for the cost now?
Forum: LTX and LSX
11-13-2015, 09:00 AM
Replies: 14
Views: 1,194
Posted By ERockZab

Re: LS1 price

Took the pan off while at the guys house and the cylinder walls looked clean, no scoring or gouging. I'll dig in to it a little deeper after I get it off the truck and on my engine stand. If it turns...
Forum: LTX and LSX
11-13-2015, 08:36 AM
Replies: 14
Views: 1,194
Posted By ERockZab

Re: LS1 price

Went and looked at the engine last night, and all that is wrong (in my judgement) with it is a rocker arm or arms. He said it would start to make noise around 2500 RPM, but nothing much before...
Forum: LTX and LSX
11-11-2015, 08:54 AM
Replies: 14
Views: 1,194
Posted By ERockZab

Re: LS1 price

Those were my thoughts pretty much. I offered $400 and I believe I've got it locked in at $500. Hoping to go check it out tomorrow after work, only sucks cause its 3 1/2 hours away haha
Forum: LTX and LSX
11-11-2015, 07:13 AM
Replies: 14
Views: 1,194
Posted By ERockZab

Re: LS1 price

Its just the motor, but it is complete oil pan to intake. He said there's 120K miles on it and no I can't hear it run.
Forum: LTX and LSX
11-10-2015, 08:56 AM
Replies: 14
Views: 1,194
Posted By ERockZab

LS1 price

Just wanting some input before I buy a Craigslist LS1 and end up regretting it. So there is a guy selling an LS1 from a 98 Camaro that he states needs a bearing replaced, but he's not sure what...
Forum: Interior
10-07-2014, 01:33 PM
Replies: 5
Views: 921
Posted By ERockZab

Re: Heating/AC Blend Doors

I actually just found a breakdown of the assembly by following a link in another thread (https://www.thirdgen.org/forums/interior/709555-interior-assembly.html) and it has part numbers and everything...
Forum: Interior
10-07-2014, 01:15 PM
Replies: 5
Views: 921
Posted By ERockZab

Re: Heating/AC Blend Doors

I didn't think about using foam weatherstripping to replace the foam. I actually have some of that on hand from when I fixed my toolbox, so I might just go that route.

Everything worked when I...
Forum: Interior
10-07-2014, 08:46 AM
Replies: 5
Views: 921
Posted By ERockZab

Heating/AC Blend Doors

Hey everyone,

I'm currently in the process of a complete rebuild and right now I'm just looking ahead for parts that I'll need while I strip the car. I want to keep A/C because it gets hot in...
Forum: Electronics
09-16-2014, 03:06 PM
Replies: 84
Views: 56,652
Posted By ERockZab

Re: Possible Useful Link for ThirdGen Wiring -

Not sure what was here, but nothing here now...
Forum: Body
07-10-2014, 11:42 AM
Replies: 13
Views: 1,008
Posted By ERockZab

Re: What's this called?

Sorry haven't looked at this thread this week...

No it will not be staying purple. Currently in a complete tear down (dash, interior, exterior, wiring harness) and going to go with a Midnight...
Forum: Body
07-01-2014, 01:24 PM
Replies: 13
Views: 1,008
Posted By ERockZab

Re: What's this called?

That's what I was planning on doing if needed, but just thought I would see if anyone knew of a full replacement piece.
Forum: Body
06-30-2014, 12:59 PM
Replies: 13
Views: 1,008
Posted By ERockZab

Re: What's this called?

When I search for that, all I get is the Sill plate that goes on top of the rocker panel and is plastic from the factory.



From what I can see, the floor pan doesn't span up into this area. The...
Forum: Body
06-30-2014, 10:42 AM
Replies: 13
Views: 1,008
Posted By ERockZab

What's this called?

Been reading on this site for quite a while now and finally got a project Camaro to work on. Its a 1992 Camaro RS, so nothing special right now, but the perfect base car to build off of.

Tore all...
Showing results 1 to 14 of 14


 
Forum Jump


All times are GMT -5. The time now is 01:08 PM.