Third Generation F-Body Message Boards

Search: Posts Made By: Scrote
Showing results 1 to 13 of 13
Search took 0.14 seconds.
Forum: Tech / General Engine
08-03-2005, 03:59 PM
Replies: 8
Views: 642
Posted By Scrote

Alright Trevor, the ESC is on the firewall, the...

Alright Trevor, the ESC is on the firewall, the code 36 is a MAF burnoff code, that will not be your issue. I have had that code on my car since I have owned it. I replaced the relay, didt cure it,...
Forum: Tech / General Engine
08-02-2005, 02:56 PM
Replies: 4
Views: 409
Posted By Scrote

Hey Trev, thats sweet man....glad she is running...

Hey Trev, thats sweet man....glad she is running for you, i got the email, and if you have any more problems give me a ring.

Peace man,

Erik
Forum: TPI
10-13-2004, 04:54 PM
Replies: 3
Views: 463
Posted By Scrote

Did you reconnect all the grounds? Sounds like...

Did you reconnect all the grounds? Sounds like you might have forgottin to tighten one down. Dont let the smoke out of your wires...check them!
Forum: Aftermarket Vendor Review
10-09-2004, 10:23 AM
Replies: 8
Views: 1,084
Posted By Scrote

He is going to go kick all their ***'s :rolleyes:

He is going to go kick all their ***'s :rolleyes:
Forum: TPI
10-08-2004, 08:23 PM
Replies: 12
Views: 2,976
Posted By Scrote

Huh..I did not read int oit enough...no that is...

Huh..I did not read int oit enough...no that is not normal. If oyu look at a TPI dyno sheet, the torque curve will platue at 4750 ish depending on CID, BUT it should not miss...it should run to 5-6k...
Forum: Aftermarket Product Review
10-08-2004, 08:18 PM
Replies: 2
Views: 536
Posted By Scrote

Re: chip difference???

There may be a difference in base codes...what is the aplication?
Forum: TPI
10-08-2004, 01:50 PM
Replies: 12
Views: 2,976
Posted By Scrote

I have to agree..:) They will fall on their...

I have to agree..:)

They will fall on their face past 4750...welcome to the wonderful world of TPI...these intakes should have came stock on 1/2 tons...

Later,

Erik
Forum: TPI
10-08-2004, 01:44 PM
Replies: 12
Views: 1,793
Posted By Scrote

24lb injectors will be enough...I have seen the...

24lb injectors will be enough...I have seen the duty cycle withthese injectors on 383's and they seem to work out great...

The Denzo 24lb is a really nice unit, you wont be dissapointed

take...
Forum: Tech / General Engine
02-24-2003, 03:10 PM
Replies: 17
Views: 755
Posted By Scrote

Oh yeah...make sure you are running on all 8, as...

Oh yeah...make sure you are running on all 8, as a dead miss will jack up your HC reading like a mo fackie... High HC is usally a mechanical problem...forgot to mention that.:D
Forum: Tech / General Engine
02-24-2003, 03:07 PM
Replies: 17
Views: 755
Posted By Scrote

Make sure that your fuel pressure regulator is in...

Make sure that your fuel pressure regulator is in good shape, if the diaphram is broken on it you will get too much HC(unburned fuel) in your exhaust. Now when your HC is high, your CO(lack of...
Forum: TPI
02-19-2003, 01:30 PM
Replies: 2
Views: 1,620
Posted By Scrote

I would also make sure that your TPS sensor sends...

I would also make sure that your TPS sensor sends a smooth voltage through out its range and that there is no dead spots...

But yeah, check to make sure you are getting good fuel pressure, and...
Forum: Mid-West Region
02-11-2001, 06:37 PM
Replies: 428
Views: 25,527
Posted By Scrote

Cool man, I know exactly where you lived...I live...

Cool man, I know exactly where you lived...I live right by the High School in Trotters Ridge.

Did you know someone named Teri Moxley-Goldsmith? I think she graduated about that time...I never...
Forum: Mid-West Region
02-09-2001, 12:23 AM
Replies: 428
Views: 25,527
Posted By Scrote

Hey Eagan Here... Randy, where in eagan do...

Hey Eagan Here...

Randy, where in eagan do you live? Did you go to Eagan High?

Yeah, I was suprised at how many MN people where on this site....CZ28.com harldy had any other than me Eric and...
Showing results 1 to 13 of 13


 
Forum Jump


All times are GMT -5. The time now is 08:53 AM.