Third Generation F-Body Message Boards

Search: Posts Made By: BIG 'G'
Showing results 1 to 14 of 14
Search took 0.28 seconds.
Forum: DIY PROM
02-07-2013, 03:40 PM
Replies: 1
Views: 694
Posted By BIG 'G'

68332 assembler?

Can anyone recomend an assembler that will work with the irapc dissassembler?
I've been trying as32 but am not having any luck, many many errors. thanks.
Forum: DIY PROM
11-09-2010, 12:46 PM
Replies: 6
Views: 786
Posted By BIG 'G'

Re: Pinout Adressing?

IF I understand this corectly the aldl stream needs to modified to read the registers and the xdf modified to display the registers when testing a pin.
Forum: DIY PROM
12-09-2008, 10:18 PM
Replies: 2
Views: 1,049
Posted By BIG 'G'

Re: mini IDE assembly problems w/$0D

Actually their are quite a few differences, I found four corrections you made at C322, C338, C754, and C77D where you switched from extended to direct addressing. This was offsetting the bin by a...
Forum: DIY PROM
12-04-2008, 10:25 PM
Replies: 2
Views: 1,049
Posted By BIG 'G'

mini IDE assembly problems w/$0D

I'm currently trying to get the OD hac by dimented to assemble, and am eccountering the exact same problems as junkcltr (see post 325 and 327 of tbi guys its time to update) with the program being...
Forum: DIY PROM
11-09-2008, 11:49 AM
Replies: 2
Views: 718
Posted By BIG 'G'

Re: $OD spark retard at tip in

Thanks for the tip Fast, however it does appear to be the difference between the to spark tables. When i copied and saved to the idle spark table it didnt get saved. Found my screw up while...
Forum: DIY PROM
11-09-2008, 12:20 AM
Replies: 2
Views: 718
Posted By BIG 'G'

$OD spark retard at tip in

Need some help trying to figure out why i'm losing 14 to 16 deg of spark when tipping in. Running a chevy1500 4.3 w/ 5spd, as you can imagine trying to take off while losing 14 deg of spark is...
Forum: DIY PROM
07-26-2008, 12:30 PM
Replies: 2
Views: 1,179
Posted By BIG 'G'

Re: $OD throttle follower ?

After a lot of time studying dimented's od hac and some experimentaion this seems to be working pretty well. Feel free to correct me if i'm wrong. I ve limited the iac position at start up from 150...
Forum: DIY PROM
06-11-2008, 09:33 PM
Replies: 2
Views: 1,179
Posted By BIG 'G'

$OD throttle follower ?

I have recently switched computers from 7747 to 7427, everything has gone well so far. Fuel curve is nearly dialed in but my biggest problem is reducing the rpm between gear shifts , rpm hangs to...
Forum: DIY PROM
05-27-2008, 09:18 PM
Replies: 6
Views: 1,085
Posted By BIG 'G'

Re: vephd blues

That's an excellent idea, will give it a try, Thanks a lot.
Forum: DIY PROM
05-25-2008, 11:43 AM
Replies: 6
Views: 1,085
Posted By BIG 'G'

Re: vephd blues

Everthing seems to crunching corectly, however for engines with one o2 sensor should the blm2 and int2 be set at zero or 128? I have it set at zero right now which seems to be why my output values...
Forum: DIY PROM
05-20-2008, 11:10 PM
Replies: 6
Views: 1,085
Posted By BIG 'G'

Re: vephd blues

Yes that is an informative thead. What i ended up doing is pasting my rpm kpa, blm ,etc info from my data log into the vephd.in file and the program ran though with no errors. However with $od...
Forum: DIY PROM
05-18-2008, 01:49 PM
Replies: 6
Views: 1,085
Posted By BIG 'G'

vephd blues

Been trying to get vephd to work with 7427 $od, frustrating to say the least. Have already modded the vephdat file to corespond with tunerpro rt csv data log. But everytime i try to run the program...
Forum: DIY PROM
10-15-2003, 08:24 PM
Replies: 12
Views: 4,532
Posted By BIG 'G'

I can cofirm a 1227747 will swap right in with no...

I can cofirm a 1227747 will swap right in with no harness changes, swapped a 747 from an astro into my 1500 truck with no problems.
Forum: DIY PROM
08-25-2003, 05:50 PM
Replies: 17
Views: 2,961
Posted By BIG 'G'

Sounds to simple but the electronicly challanged...

Sounds to simple but the electronicly challanged need more details, when you say put a 28 pin zif on the board, do you mean solder it on the board in place of the factory 24pin recepticle? Or is...
Showing results 1 to 14 of 14


 
Forum Jump


All times are GMT -5. The time now is 10:24 AM.