Third Generation F-Body Message Boards

 
Page 1 of 10
1
2
3
4
5
Last »
Search: Posts Made By: midias
Showing results 1 to 50 of 500
Search took 0.10 seconds.
Forum: Alternative Port EFI Intakes
Yesterday, 09:23 AM
Replies: 56
Views: 5,658
Posted By midias

Re: Sniper EFI

170 miles of testing later and no issues the car is running nice and responding good to timing changes. Right now running 27 idle 34 WOT and 40 cruise with the table smoothed a bit. Need more testing...
Forum: Fabrication
04-27-2024, 10:35 AM
Replies: 42
Views: 1,712
Posted By midias

Re: AWD 3rd gen build

Holy crap that's a lot of effort but nice job I'm going to keep following this I can't wait to see the final product
Forum: Cooling
04-18-2024, 05:57 PM
Replies: 19
Views: 365
Posted By midias

Re: Cooling Q…not sure of problem

I ran one of these on my last build for a decade. Matched my fan switch and IR temp gun almost perfectly

https://www.amazon.com/Dorman-7-120-Water-Temperature-Gauge/dp/B002ET0P9Q
Forum: Electronics
04-17-2024, 01:57 PM
Replies: 21
Views: 26,346
Posted By midias

Re: 1984 Trans Am Headlight/Relay Information

I bought this for my 84 works great
https://rodneydickman.com/product_info.php?products_id=418
Forum: Wheels and Tires
04-17-2024, 12:24 PM
Replies: 12
Views: 317
Posted By midias

Re: Do firebird rims normally get the Pontiac polished off?

Those letters are deep set I would be pissed and demand a replacement set or compensation.
Forum: Engine/Drivetrain/Suspension Wanted
04-17-2024, 12:17 PM
Replies: 3
Views: 136
Posted By midias

Re: 1/4 turn fasteners

look for Dzus fasteners
Forum: Cooling
04-17-2024, 06:53 AM
Replies: 19
Views: 365
Posted By midias

Re: Cooling Q…not sure of problem

The data is a little inconsistent because of tolerance but the 505 switch should be 221 +- 8 Fahrenheit nominal
Forum: Cooling
04-16-2024, 03:22 PM
Replies: 19
Views: 365
Posted By midias

Re: Cooling Q…not sure of problem

Sounds like a factory gauge that ready too high. Mine would read 260 when my factory switch came on at 235. Grab a 1989 turbo trans am switch comes on at 212 and off at 195 and measure temp with the...
Forum: Cooling
04-16-2024, 03:10 PM
Replies: 21
Views: 352
Posted By midias

Re: Electric Fan doesn’t start when reaches temp

Chances are the switch is coming on at the right temp but the temp gauge is showing the wrong value. If you want a lower one get a 1989 turbo trans am switch 210 on 195 off.
Forum: Alternative Port EFI Intakes
04-11-2024, 03:07 PM
Replies: 5
Views: 204
Posted By midias

Re: fitec

I am not quite sure what you are asking, if English is you second language you might want to see if google translate can help.

If I am reading right you think you have low fuel pressure even with...
Forum: Transmissions and Drivetrain
04-08-2024, 12:48 PM
Replies: 5
Views: 219
Posted By midias

Re: Clutch master cylinder replacement

I have done it both ways
Forum: Members Firebirds
04-07-2024, 04:17 PM
Replies: 83
Views: 5,999
Posted By midias

Re: My new 1984 TA project

Over the winter I installed The holley hyperspark 2.0 and a few other goodies. I had some issues that I thought were RFI turned out to be a loose fuse but it's running right now and I finally had a...
Forum: Tech / General Engine
04-04-2024, 08:40 PM
Replies: 14
Views: 554
Posted By midias

Re: Vortec vs Promaxx vs AFR enforcer vs Jegs aluminum

I ran a RPM performer dual plane with an open spacer no issues. I am running a RPM air gap with a factory milled divider and a four hole spacer no issues. The new sniper 2.0 system which you should...
Forum: Exhaust
04-03-2024, 06:41 AM
Replies: 38
Views: 13,639
Posted By midias

Re: header choices

When I made my friend's y pipe I used that merger about the best thing flowmaster makes
Forum: Interior
04-02-2024, 11:11 PM
Replies: 14
Views: 521
Posted By midias

Re: My local public library printed me some new tail light nuts and trim clips

Mine had some sort of foam seal but it was pretty well deteriorated so I put a little 3M strip caulk under me
Forum: Exhaust
04-02-2024, 01:17 PM
Replies: 38
Views: 13,639
Posted By midias

Re: header choices

Its still a good combo but the doughs Y pipe merger sucks get some 3" pipe and cut and weld it up proper.
...
Forum: Interior
04-02-2024, 10:06 AM
Replies: 14
Views: 521
Posted By midias

Re: My local public library printed me some new tail light nuts and trim clips

That is fantastic, never heard of a library doing that
Forum: Tech / General Engine
03-29-2024, 08:33 AM
Replies: 14
Views: 554
Posted By midias

Re: Vortec vs Promaxx vs AFR enforcer vs Jegs aluminum

I love my sniper system and the new version 2.0 has addressed many of the complaints with the original. I tuned my carb with a wide band gauge and vacuum gauge and EFI makes more power across all...
Forum: TBI
03-26-2024, 01:49 PM
Replies: 2
Views: 113
Posted By midias

Re: Still no spark

I would check the +12V ign going to the distributor
Forum: Tech / General Engine
03-26-2024, 01:43 PM
Replies: 14
Views: 554
Posted By midias

Re: Vortec vs Promaxx vs AFR enforcer vs Jegs aluminum

I have the promaxx 2151 185cc heads. I bought them back when it was patriot heads. I had to replace the springs because the dampers broke. They sent some replacements for free and same thing. I...
Forum: Electronics
03-25-2024, 12:12 PM
Replies: 8
Views: 298
Posted By midias

Re: What is the best way to add multiple ignition sources

to use relays and make a distribution block from 12V ignition you can do something like this
...
Forum: TBI
03-25-2024, 10:59 AM
Replies: 11
Views: 412
Posted By midias

Re: Have a 350 flat tappet lo5, best route to power?

Swap the heads and put a roller conversion cam in it. Would need more info on what pistons are in the motor and what your final goals are before choosing the cam and heads
Forum: TBI
03-16-2024, 01:55 PM
Replies: 25
Views: 813
Posted By midias

Re: TBI to Holley Sniper EFI Swap?

Holly just redesigned the entire system to deal with a lot of complaints from the old ones although I've never had an issue I thought I had an RFI problem turned out to be a loose fuse.
Forum: Tech / General Engine
03-15-2024, 09:54 PM
Replies: 28
Views: 2,217
Posted By midias

Re: What's needed for CC Carb/sp350 combo?

That's awesome, the computer controlled carb does not get nearly as much love as it should. Too many Edelbrock downgrades out there I love seeing someone upgrade back to what it should be.
Forum: Transmissions and Drivetrain
03-15-2024, 03:05 PM
Replies: 3
Views: 185
Posted By midias

Re: Posi Question

you can get 90-92 28 spline axles and it will work
Forum: TBI
03-15-2024, 11:13 AM
Replies: 25
Views: 813
Posted By midias

Re: TBI to Holley Sniper EFI Swap?

Edelbrock air gap also ran a RPM performer for a while. For about 3 years I ran a MSD 8360 with SS coil. I am in the process of changing it to their hyperspark now no idea about a factory...
Forum: Alternative Port EFI Intakes
03-14-2024, 09:26 PM
Replies: 56
Views: 5,658
Posted By midias

Re: Sniper EFI

Did some more work tonight and ran the car for many minutes letting fans cycle on and off a few times. Absolutely no issues started and restarted easily no stalling. So I started cleaning up some...
Forum: TBI
03-14-2024, 02:48 PM
Replies: 25
Views: 813
Posted By midias

Re: TBI to Holley Sniper EFI Swap?

They sell a TCC lock up kit


https://www.holley.com/products/fuel_systems/fuel_injection/sniper_efi/ignition_and_fuel_systems/transmission_control/parts/551-103

So far I have really liked my...
Forum: Alternative Port EFI Intakes
03-13-2024, 10:59 PM
Replies: 56
Views: 5,658
Posted By midias

Re: Sniper EFI

Went back to troubleshooting today was still having issues so I decided to redo all my wires again see how far away I could get everything. When I went to start again my LCD said no ECU no data...
Forum: Suspension and Chassis
03-11-2024, 11:12 AM
Replies: 2
Views: 239
Posted By midias

Re: Power Steering Cooler Delete?

Drove my last firebird for 10 years with no cooler. Came that way and I had no idea it existed
Forum: Alternative Port EFI Intakes
03-08-2024, 07:36 PM
Replies: 56
Views: 5,658
Posted By midias

Re: Sniper EFI

Tried a couple ferrite beads in a few places definitely improved performance. I also grabbed some emi shielding that can go over wires in case I need it. But I am still having emi issues one...
Forum: Tech / General Engine
03-04-2024, 11:26 PM
Replies: 18
Views: 12,756
Posted By midias

Re: Sure I didnt dream this. 98 vortec block drilling the water pump bypass hole.

Nice job no need to drill it out to 3/8 NPT then which is a 37/64 drill before tap
Forum: Tech / General Engine
03-04-2024, 08:51 PM
Replies: 18
Views: 12,756
Posted By midias

Re: Sure I didnt dream this. 98 vortec block drilling the water pump bypass hole.

IIRC the hole is threaded 3/8 NPT. A little sealer and a plug and you should be good to go
Forum: Alternative Port EFI Intakes
03-03-2024, 07:46 PM
Replies: 56
Views: 5,658
Posted By midias

Re: Sniper EFI

Had my first start up with the distributor today it was a mixed bag of success and failure. I left a bunch of the wires really long just to test it before I bundled everything together. Discovered...
Forum: Body
02-29-2024, 01:51 PM
Replies: 26
Views: 1,109
Posted By midias

Re: Trans Am totaled - advice needed

A good lesson for everyone who restores cars. Make sure your policy has a value you can live with most insurance companies allow extra coverage
Forum: Fabrication
02-20-2024, 10:10 AM
Replies: 42
Views: 1,712
Posted By midias

Re: AWD 3rd gen build

Following this is awesome
Forum: Engine/Drivetrain/Suspension Parts for Sale
02-14-2024, 11:20 AM
Replies: 5
Views: 349
Posted By midias

1LE Aluminum Driveshaft for sale

Camaro 1LE driveshaft for sale looking for local pickup near rochester NY $200
...
Forum: Interior
02-14-2024, 07:40 AM
Replies: 21
Views: 619
Posted By midias

Re: Too tall for a firebird?

Last year I helped out someone in a similar situation for a 60s mustang we ended up making seat brackets and putting them under the car and moving the seat back 5 or 6 inches then a thin headliner...
Forum: Tech / General Engine
02-14-2024, 07:17 AM
Replies: 20
Views: 748
Posted By midias

Re: Low Voltage to Distributor

Use your ignition +12V wire to activate a coil on a relay and then bring battery voltage over. Will be a cleaner signal and full power
Forum: Transmissions and Drivetrain
02-12-2024, 10:48 AM
Replies: 21
Views: 522
Posted By midias

Re: 1986 Trans AM 700R4 to T5 VSS question

I will update when we finish the swap probably in May. We are preparing for it now. I just did an auto to manual conversion on my last build so it is fresh in my mind
Forum: Transmissions and Drivetrain
02-11-2024, 04:12 PM
Replies: 21
Views: 522
Posted By midias

Re: 1986 Trans AM 700R4 to T5 VSS question

Is this the right thing?

​​​​​​Also any idea what gears I'll need for a 373 rear? And if they're still available at all
...
Forum: Engine/Drivetrain/Suspension Wanted
02-08-2024, 11:44 AM
Replies: 6
Views: 575
Posted By midias

Re: throttle cable bracket for miniram

Hahaha must have scrolled to far and responded to the wrong post
Forum: Engine/Drivetrain/Suspension Wanted
02-08-2024, 10:53 AM
Replies: 6
Views: 575
Posted By midias

Re: throttle cable bracket for miniram

Glad it worked out for you. Mine has been fine for 2500 miles and $20 is a good price
Forum: Body
02-06-2024, 08:46 PM
Replies: 11
Views: 411
Posted By midias

Re: Spare tire well rust.. repair?

If it makes you feel any better my friend had a nearly rust free firebird except for that one area. Everything else the frame the floor it's all perfect.
Forum: Alternative Port EFI Intakes
02-06-2024, 07:36 PM
Replies: 56
Views: 5,658
Posted By midias

Re: Sniper EFI

More accurate timing control and the ability to change your timing curve with a laptop. You can also tune a lot better and theoretically gain more horsepower and better gas mileage. In the spring...
Forum: Transmissions and Drivetrain
02-06-2024, 10:41 AM
Replies: 21
Views: 522
Posted By midias

Re: 1986 Trans AM 700R4 to T5 VSS question

Thanks maybe I will sell the other one on eBay. I wonder if I can test it.

Back to cable x
Forum: Body
02-06-2024, 10:36 AM
Replies: 11
Views: 411
Posted By midias

Re: Spare tire well rust.. repair?

It's possible I had to do one vertical strip. Only way to know is start sanding. I had to re weld the spare tire bracket to the lower body
Forum: Body
02-06-2024, 10:10 AM
Replies: 11
Views: 411
Posted By midias

Re: Spare tire well rust.. repair?

That was one of my first ever body repairs. Used an old flux welder, made a patch then coated the inside with POR15. Not my best work but held for 10 years before I moved to another project. You...
Forum: Transmissions and Drivetrain
02-05-2024, 04:37 PM
Replies: 21
Views: 522
Posted By midias

Re: 1986 Trans AM 700R4 to T5 VSS question

Lol look what I found in my parts bin

https://cimg2.ibsrv.net/gimg/www.thirdgen.org-vbulletin/2000x1504/img_20240205_173617005_df21cd0d6c3e972ae4a4cf77ed563115ae3032d6.jpg
Showing results 1 to 50 of 500
 
Page 1 of 10
1
2
3
4
5
Last »


 
Forum Jump


All times are GMT -5. The time now is 01:46 PM.