How do i siphon gas out of my tank?
#1
Supreme Member
Thread Starter
iTrader: (8)
Join Date: Jan 2000
Location: Macedonia ,OH
Posts: 3,968
Likes: 0
Received 1 Like
on
1 Post
Car: Formula
Engine: 6.0 LSX
Transmission: 4L60E
Axle/Gears: 9 Bolt 3:27
How do i siphon gas out of my tank?
I have stuck a 10 ft piece of hose down the tank and its not even touching the gas. Whats going on? is there a trick to this. It feels like I'm hitting a spring or something.
#2
Moderator
Join Date: Jul 1999
Location: 51°N 114°W, 3500'
Posts: 17,110
Likes: 0
Received 120 Likes
on
101 Posts
Car: 87 IROC L98
Engine: 588 Alcohol BBC
Transmission: Powerglide
Axle/Gears: Ford 9"/31 spline spool/4.86
Welcome to GM's anti theft system. It's almost impossible to siphon gas from a GM tank now.
#3
Wiggle it in and out while rotating it. You'll drive her nuts. I mean, you'll dip it in eventually. Helps if it's slightly curved (should already be curved to the left, right?).
If you get sick if doing that, you could go under the car and unhook the filter and stick the tube onto the fuel line, then run 12 volts to the pump (you can do that at the ALDL connector).
If you get sick if doing that, you could go under the car and unhook the filter and stick the tube onto the fuel line, then run 12 volts to the pump (you can do that at the ALDL connector).
#5
Supreme Member
Join Date: Sep 2001
Location: Tallahassee, FL. USA
Posts: 1,266
Likes: 0
Received 3 Likes
on
3 Posts
Car: 92 Camaro RS
Engine: 350 Crate Motor
Transmission: Tremec TKO
Axle/Gears: 10 Bolt 3.73
[QUOTE]Originally posted by Jza:
[B]Wiggle it in and out while rotating it. You'll drive her nuts. I mean, you'll dip it in eventually. Helps if it's slightly curved (should already be curved to the left, right?).
Nice visual.....
-Rich-
[B]Wiggle it in and out while rotating it. You'll drive her nuts. I mean, you'll dip it in eventually. Helps if it's slightly curved (should already be curved to the left, right?).
Nice visual.....
-Rich-
#6
Supreme Member
Join Date: Mar 2000
Location: Central NJ, USA
Posts: 13,414
Likes: 0
Received 6 Likes
on
6 Posts
Car: 1986 Firebird
Engine: 2.8 V6
Transmission: 700R4
Well here's something that's kind of cool; GM's hung the fuel sending unit right in front of the filler neck opening! Yep, that's what you're hitting with the hose. I assume it was put there to wash down the fuel sending unit.
Are you replacing the electric fuel pump? If so, the thing might have enough "kick" to drain the tank for you. Unhook the fuel filter, and lead a hose from the feed line to a gas can. Put the key to "on" (so you can watch the gas gauge). Apply +12 to the fuel pump "test connector", which will energize the pump. Remove the +12 when your gas gauge shows empty. Oh- do this outside, and don't smoke, or drop any wrenches, or play with explosives near the gas. Okay?
------------------
-Tom P (Hot rodded 1986 Firebird 2.8l)
Are you replacing the electric fuel pump? If so, the thing might have enough "kick" to drain the tank for you. Unhook the fuel filter, and lead a hose from the feed line to a gas can. Put the key to "on" (so you can watch the gas gauge). Apply +12 to the fuel pump "test connector", which will energize the pump. Remove the +12 when your gas gauge shows empty. Oh- do this outside, and don't smoke, or drop any wrenches, or play with explosives near the gas. Okay?
------------------
-Tom P (Hot rodded 1986 Firebird 2.8l)
Trending Topics
#8
Supreme Member
Thread Starter
iTrader: (8)
Join Date: Jan 2000
Location: Macedonia ,OH
Posts: 3,968
Likes: 0
Received 1 Like
on
1 Post
Car: Formula
Engine: 6.0 LSX
Transmission: 4L60E
Axle/Gears: 9 Bolt 3:27
Well There was half a tank and we couldnt get it out so me and my dad got under there and got it out. It was SO easy getting it out. Why does everybody complain about bending the neck? We rolled it forward while gently pulling out and wham dropped right out. Very Easy Thanks for the suggs guys
Thread
Thread Starter
Forum
Replies
Last Post
Bohemian
History / Originality
24
08-15-2017 05:11 PM